Snapper Network Card 1695295 User Manual

Light Kit  
Part No. 1695295  
Installation  
For Axion and 150Z Zero Turn Models  
Instructions  
1
1
2
4
2
4
5
6
3
3
Kit Contents:  
Ref. Part No. Qty. Description  
1
2
3
4
N/A  
N/A  
N/A  
1726801  
2
2
2
2
NUT, Hex, 5/16-18  
LOCKWASHER, 5/16  
CARRIAGE BOLT, 5/16-18 x 1  
HEADLIGHT ASSEMBLY,  
(Includes Ref. Nos. 1, 2, & 3)  
SWITCH, Headlight  
7
5
6
7
1716951  
2172434  
1726796  
1
2
1
CLIP, Wire  
HARNESS, Wire  
Figure 1. Contents  
WARNING  
Before beginning any service work turn off the  
PTO, set the parking brake, turn off the ignition,  
remove the key, and disconnect the spark plug  
wire(s).  
B
C
D
A
INSTALLATION  
1. Remove 1/4-20 x 5/8 capscrews (A, Figure 2) and  
cover (B).  
F
2. Install light assembly (F) and secure with 5/16 lock-  
washer (D) and 5/16-18 nut (C).  
E
3. Reinstall cover (B) and secure with 1/4-20 capscrews  
(A).  
4. Repeat steps 1 through 3 for other side of unit.  
Figure 2. Light Installation  
A. Capscrews, 1/4-20 x 5/8  
B. Cover  
C. Nut, 5/16-18  
D. Lockwasher, 5/16  
E. Bracket  
F. Light Assembly  
1
 
Light Kit  
Installation Instructions  
Note: The side of the headlight wire harness with the  
ribbed plastic cover (C, Figure 6) connects to the left side  
light. The side of the headlight wire harness with the  
braided cover goes to the right side light.  
D
13. Connect harness plug (B, Figure 6) to the back of the  
headlight (A). Make sure the connector is fully seat-  
ed into the light.  
E
C
14. Slide wire clip (D) onto the back side of bracket (E)  
as shown. Push down to secure.  
B
15. Slide headlight wire harness (C) into wire clip (D).  
Pull slack out of headlight wire harness (C) toward  
engine compartment. Route wires so they do not  
contact hot or moving components.  
A
16. Repeat step 13, 14 & 15 on the other side of unit.  
17. Lower seat to normal operating position.  
18. Operate control levers to be sure wires, clips and  
lights do not make contact with levers. If so, readjust  
components so there is no interference.  
Figure 6. Light Connection  
A. Light  
B. Harness Plug  
19. Reconnect spark plug.  
C. Headlight Wire Harness, w/Ribbed Plastic Cover  
D. Wire Clip  
E. Bracket  
OPERATION  
1. Start the unit using normal procedures. After the unit  
has warmed up and is operating at full throttle the  
lights may be turned on.  
2. Turn the lights off before turning off the unit. If lights  
are left on with out running the unit they will drain the  
battery.  
Note: The headlights may dim if the RPM’s of the engine  
become to low.  
3
 
Installation Instructions  
Light Kit  
NOTES  
Form No. 1734309  
Revision:00  
TP 200-4583-00-AT-SN  
MANUFACTURING, INC.  
Briggs & Stratton Yard Power Products Group  
Copyright © 2007 Briggs & Stratton Corporation  
Milwaukee, WI USA. All Rights Reserved  
500 N Spring Street / PO Box 997  
Port Washington, WI 53074-0997 USA  
4
 

Sony DVD Recorder RDR HX780 User Manual
Sony Home Theater Screen CPD E400E User Manual
Sony Portable Speaker SA VE356T User Manual
Sony Projection Television KP 51HW40 User Manual
Sony Stereo Receiver STR DE685 User Manual
Soundstream Technologies Stereo Amplifier D200 II User Manual
Spalding Fitness Equipment M662004 User Manual
Sunbeam Oxygen Equipment SCM1100 User Manual
SUPER MICRO Computer Computer Hardware AOCS2308LL8E User Manual
Tapco Musical Instrument Mix100 User Manual