Symphonic DVD VCR Combo CWF803 User Manual

OWNER’S  
MANUAL  
DVD PLAYER with VIDEO CASSETTE RECORDER  
CWF803  
ReWritable  
Recordable  
POWER  
OPEN/CLOSE  
CH-UP  
STOP/EJECT  
FF  
OUTPUT  
DVD  
STOP  
FWD  
REW  
REV  
PLAY  
VCR  
REC  
TIMER  
REC  
VIDEO  
AUDIO  
PLAY  
CH-DOWN  
PLAY  
DISC IN  
Please read before using this equipment.  
 
IMPORTANT SAFEGUARDS  
1. Read Instructions - All the safety and operating instructions  
ing of the mast and supporting structure, grounding of the  
lead-in wire to an antenna discharge unit, size of grounding  
conductors, location of antenna-discharge unit, connection  
to grounding electrodes, and requirements for the grounding  
electrode. (Fig. A)  
should be read before the appliance is operated.  
2. Retain Instructions- The safety and operating instructions  
should be retained for future reference.  
3. Heed Warnings - All warnings on the appliance and in the  
operating instructions should be adhered to.  
4. Follow Instructions - All operating and use instructions  
should be followed.  
FIGURE A  
ANTENNA  
LEAD  
EXAMPLE OF ANTENNA GROUNDING  
WIRE  
AS PER NATIONAL ELECTRICAL CODE  
GROUND  
CLAMP  
5. Cleaning - Unplug this video product from the wall outlet  
before cleaning. Do not use liquid cleaners or aerosol clean-  
ANTENNA  
DISCHARGE UNIT  
(NEC SECTION 810-20)  
ers.  
Use  
a
damp  
cloth  
for  
cleaning.  
EXCEPTION: A product that is meant for uninterrupted ser-  
vice and, that for some specific reason, such as the possibil-  
ity of the loss of an authorization code for a CATV convert-  
er, is not intended to be unplugged by the user for cleaning  
or any other purpose, may exclude the reference to unplug-  
ging the appliance in the cleaning description otherwise  
required in item 5.  
6. Attachments - Do not use attachments not recommended by  
the video product manufacturer as they may cause hazards.  
7. Water and Moisture- Do not use this video product near  
water, for example, near a bath tub, wash bowl, kitchen sink,  
or laundry tub, in a wet basement, or near a swimming pool,  
and the like.  
ELECTRIC  
SERVICE  
EQUIPMENT  
GROUNDING CONDUCTORS  
(NEC SECTION 810-21)  
GROUND CLAMP  
NEC – NATIONAL ELECTRICAL CODE  
S2898A  
POWER SERVICE GROUNDING  
ELECTRODE SYSTEM  
(NEC ART 250, PART H)  
14. Lightning - For added protection for this video product dur-  
ing a lightning storm, or when it is left unattended and  
unused for long periods of time, unplug it from the wall out-  
let and disconnect the antenna or cable system. This will pre-  
vent damage to the video product due to lightning and  
power-line surges.  
15. Power Lines - An outside antenna system should not be  
located in the vicinity of overhead power lines or other elec-  
tric light or power circuits, or where it can fall into such  
power lines or circuits. When installing an outside antenna  
system, extreme care should be taken to keep from touching  
such power lines or circuits as contact with them might be  
fatal.  
8. Accessories - Do not place this video  
product on an unstable cart, stand, tripod,  
bracket, or table. The video product may  
fall, causing serious injury to a child or  
adult, and serious damage to the appli-  
ance. Use only with a cart, stand, tripod,  
bracket, or table recommended by the  
16. Overloading - Do not overload wall outlets and extension  
manufacturer, or sold with the video  
cords as this can result in a risk of fire or electric shock.  
product. Any mounting of the appliance should follow the  
manufacturer's instructions and should use a mounting  
accessory recommended by the manufacturer. An appliance  
and cart combination should be moved with care. Quick  
stops, excessive force, and uneven surfaces may cause the  
appliance and cart combination to overturn.  
17. Object and Liquid Entry - Never push objects of any kind  
into this video product through any openings as they may  
touch dangerous voltage points or short-out parts that could  
result in a fire or electric shock. Never spill liquid of any  
kind on the video product.  
18. Servicing - Do not attempt to service this video product  
yourself as opening or removing covers may expose you to  
dangerous voltage or other hazards. Refer all servicing to  
qualified service personnel.  
19. Damage Requiring Service - Unplug this video product from  
the wall outlet and refer servicing to qualified service per-  
sonnel under the following conditions:  
a. When the power-supply cord or plug is damaged.  
b. If liquid has been spilled, or objects have fallen into the  
9. Ventilation - Slots and openings in the cabinet are provided  
for ventilation and to ensure reliable operation of the video  
product and to protect it from overheating, and these open-  
ings must not be blocked or covered. The openings should  
never be blocked by placing the video product on a bed,  
sofa, rug, or other similar surface. This video product should  
not be placed in a built-in installation such as a bookcase or  
rack unless proper ventilation is provided or the manufac-  
turer's instructions have been adhered to.  
10. Power Sources - This video product should be operated only  
from the type of power source indicated on the marking  
label. If you are not sure of the type of power supply to your  
home, consult your appliance dealer or local power compa-  
ny. For products intended to operate from battery power, or  
other sources, refer to the operating instructions.  
11. Grounding or Polarization - This video product is equipped  
with a polarized alternating-current line plug (a plug having  
one blade wider than the other). This plug will fit into the  
power outlet only one way. This is a safety feature. If you are  
unable to insert the plug fully into the outlet, try reversing  
the plug. If the plug should still fail to fit, contact your elec-  
trician to replace your obsolete outlet. Do not defeat the  
safety purpose of the polarized plug.  
12. Power Cord Protection - Power supply cords should be rout-  
ed so that they are not likely to be walked on or pinched by  
items placed upon or against them, paying particular atten-  
tion to cords at plugs, convenience receptacles, and the point  
where they exit from the appliance.  
video product.  
c. If the video product has been exposed to rain or water.  
d. If the video product does not operate normally by following  
the operating instructions. Adjust only those controls that  
are covered by the operating instructions as an improper  
adjustment of other controls may result in damage and will  
often require extensive work by a qualified technician to  
restore the video product to its normal operation.  
e. If the video product has been dropped or damaged in any  
way.  
f. When the video product exhibits a distinct change in perfor-  
mance this indicates a need for service.  
20. Replacement Parts - When replacement parts are required,  
be sure the service technician has used replacement parts  
specified by the manufacturer or have the same characteris-  
tics as the original part. Unauthorized substitutions may  
result in fire, electric shock or other hazards.  
21. Safety Check - Upon completion of any service or repairs to  
this video product, ask the service technician to perform  
safety checks to determine that the video product is in prop-  
er operating condition.  
22. Heat - This video product should be situated away from heat  
sources such as radiators, heat registers, stoves, or other  
products (including amplifiers) that produce heat.  
13. Outdoor Antenna Grounding - If an outside antenna or cable  
system is connected to the video product, be sure the anten-  
na or cable system is grounded so as to provide some pro-  
tection against voltage surges and built-up static charges.  
Article 810 of the National Electrical Code, ANSI/NFPA  
No. 70, provides information with regard to proper ground-  
EN  
Download from Www.Somanuals.com3. All Manuals Search And Download.  
1L25  
A NOTE ABOUT RECYCLING  
This product’s packaging materials are recyclable and can be reused. Please dispose of all materials in  
accordance with your local recycling regulations.  
Batteries should never be thrown away or incinerated but disposed of in accordance with your local  
regulations concerning chemical wastes.  
The serial number of this product may be found on the back of the DVD/VCR COMBINATION UNIT. This ser-  
ial number is unique to your machine. You should record the number and other vital information here and retain  
this book as a permanent record of your purchase to aid identification in case of theft. Serial numbers are not  
kept on file.  
Date of Purchase  
Dealer Purchase from  
Dealer Address  
Dealer Phone No.  
Model No.  
Serial No.  
ABOUT COPYRIGHT  
Unauthorized copying, broadcasting, public performance and lending of discs are prohibited.  
This product incorporates copyright protection technology that is protected by method claims of certain U.S.  
patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use  
of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for  
home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse  
engineering or disassembly is prohibited.  
SUPPLIED ACCESSORIES  
RF Cable  
Owner’s Manual  
Remote control Two AA batteries  
A/V cables  
Owner’s  
Manual  
(approx. 3 feet (100 cm) long)  
(WPZ0102TM015)  
(NA220UD) or  
(NA270UD)  
(WPZ0901TM002)  
(0VMN03821)  
(WPZ0102LTE01)  
SYMBOLS USED IN THIS MANUAL  
The following symbols below appear in some headings and notes in this manual, with the following meanings  
VCR  
: Description refers to playback of video cassette tapes.  
DVD-V  
: Description refers to playback of DVD video discs.  
CD  
: Description refers to playback of audio CDs.  
MP3  
: Description refers to playback of MP3 discs.  
QUICK  
: Description refers to the items to be set in the QUICK mode.  
EN  
Download from Www.Somanuals.com4. All Manuals Search And Download.  
1L25  
TABLE OF CONTENTS  
LASER SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2  
PLAYING A DISC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22  
BASIC PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22  
GENERAL FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22  
PAUSE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22  
DISC MENU. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23  
TITLE MENU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23  
STEP BY STEP PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . 23  
RESUME . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23  
FAST FORWARD / REVERSE SEARCH . . . . . . . . . . . . . . . 23  
SLOW FORWARD / SLOW REVERSE . . . . . . . . . . . . . . . . 23  
ZOOM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24  
TRACK (CD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24  
TITLE / CHAPTER SEARCH. . . . . . . . . . . . . . . . . . . . . . . . 24  
TIME SEARCH. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24  
REPEAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25  
PROGRAM (CD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25  
RANDOM PLAYBACK (CD). . . . . . . . . . . . . . . . . . . . . . . . 26  
MP3 PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26  
ON-SCREEN INFORMATION . . . . . . . . . . . . . . . . . . . . . . . 26  
TRACK SELECTION (MP3) . . . . . . . . . . . . . . . . . . . . . . . . 26  
RANDOM PLAYBACK (MP3). . . . . . . . . . . . . . . . . . . . . . . 27  
PROGRAM (MP3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27  
AUDIO LANGUAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27  
STEREO SOUND MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . 27  
SUBTITLE LANGUAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . 27  
CAMERA ANGLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27  
CHANGING THE ON-SCREEN DISPLAY . . . . . . . . . . . . . 28  
PARENTAL CONTROL . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28  
MARKER SETUP SCREEN . . . . . . . . . . . . . . . . . . . . . . . . . 29  
DVD SETUP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29  
AUDIO SETTING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29  
BLACK LEVEL SETTING . . . . . . . . . . . . . . . . . . . . . . . . . . 30  
VIRTUAL SURROUND . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30  
DISPLAY SETTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30  
LANGUAGE SETTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31  
TROUBLESHOOTING GUIDE. . . . . . . . . . . . . . . . . . . . . . 32  
MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33  
SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34  
IMPORTANT SAFEGUARDS . . . . . . . . . . . . . . . . . . . . . . . . 3  
ABOUT COPYRIGHT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4  
SUPPLIED ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . 4  
SYMBOLS USED IN THIS MANUAL. . . . . . . . . . . . . . . . . . 4  
FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6  
PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6  
ABOUT THE DISCS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7  
PLAYABLE DISCS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7  
DISC TYPES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7  
OPERATING CONTROLS AND FUNCTIONS. . . . . . . . . . . 8  
LOADING THE BATTERIES . . . . . . . . . . . . . . . . . . . . . . . . 11  
VCR/DVD SWITCHING . . . . . . . . . . . . . . . . . . . . . . . . . . . 12  
HOOKUPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13  
CONNECTING TO A TV WITHOUT A/V TERMINALS. . . 13  
CONNECTING TO A TV WITH A/V TERMINALS. . . . . . . 13  
CONNECTING TO A TV THAT HAS AN S-VIDEO INPUT  
JACK OR COMPONENT VIDEO IN JACKS. . . . . . . . . . . . 14  
CONNECTING TO A STEREO AMPLIFIER EQUIPPED  
WITH DIGITAL INPUT JACKS SUCH AS MD DECK OR  
DAT DECK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14  
CONNECTING TO A RECEIVER WITH  
DOLBY DIGITAL DECODER . . . . . . . . . . . . . . . . . . . . . . . 15  
CONNECTING TO AN ANALOG AUDIO SYSTEM. . . . . . 15  
SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16  
AUTOMATIC CHANNEL SET UP. . . . . . . . . . . . . . . . . . . . 16  
TO CHANGE THE ON-SCREEN LANGUAGE. . . . . . . . . . 17  
CLOCK SET UP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17  
PLAYBACK FUNCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . 18  
NORMAL PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18  
AUTO REPEAT PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . 18  
SEARCH FUNCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18  
RECORDING FUNCTION . . . . . . . . . . . . . . . . . . . . . . . . . 19  
NORMAL RECORDING . . . . . . . . . . . . . . . . . . . . . . . . . . . 19  
OTR (One Touch Recording). . . . . . . . . . . . . . . . . . . . . . . . . 19  
TIMER RECORDING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19  
HINTS FOR TIMER RECORDING . . . . . . . . . . . . . . . . . . . 20  
SPECIAL FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21  
COPYING A VIDEO TAPE. . . . . . . . . . . . . . . . . . . . . . . . . . 21  
AUTO REWIND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21  
REAL TIME TAPE COUNTER. . . . . . . . . . . . . . . . . . . . . . . 21  
EN  
Download from Www.Somanuals.com5. All Manuals Search And Download.  
1L25  
FEATURES  
¡Virtual Surround Sound  
DVD  
Mode  
¡Component Video Out Jacks  
¡Dolby Digital sound  
Jacks located on the back of the DVD/VCR COMBINA-  
TION UNIT which are used to send high-quality video to  
a TV via Component Video In Jacks.  
This DVD/VCR COMBINATION UNIT can output a  
Dolby Digital audio signal.  
¡Pause/fast/slow/step playback  
¡Bit rate indication  
¡Random playback for audio CD and MP3  
¡Program playback for audio CD and MP3  
¡DVD menus in a desired language  
¡DRC (Dynamic range control)  
You can control the range of sound volume.  
¡Black Level Setting  
¡Screen saver/Auto power-off functions  
The screen saver program starts when there is no input  
from the player for five minutes in the stop mode. When  
the screen saver program is activated for 30 minutes, the  
power automatically comes off.  
VCR  
Mode  
Hardware specifications  
¡Auto Head Cleaner  
¡Trilingual on-screen menu display selectable in  
English, French, or Spanish  
¡Subtitles in a desired language  
¡Selecting a camera angle  
¡181 channel capability PLL frequency synthesiz-  
er tuner with direct station call  
(A cable converter box may be necessary to view scram-  
¡Choices for audio language and sound mode  
¡Parental lock  
bled cable channels.)  
¡Automatic detection of discs  
This player automatically detects if the loaded disc is  
Automatic functions  
DVD, audio CD or MP3 on disc.  
¡Auto power on system  
Automatically turns the VCR on when you insert the cas-  
sette.  
¡Playing an audio CD with MP3 files  
¡Direct Search  
¡Digital Auto Tracking (DTR)  
¡On-screen display  
Information about the current operation can be displayed  
on the TV screen, allowing you to confirm the currently  
active functions (such as program playback), on the TV  
screen using the remote control.  
Playback  
¡Auto Repeat  
¡2 Step Picture Search Operation  
¡Index Search  
¡Search  
¡Time Search  
Chapter search / Title search / Track search / Time search  
Recording  
¡Repeat  
Chapter / Title / Track / Group / All / A-B  
¡1Year, 8 events (including Daily and WeeklyTimer  
Recording)  
¡Zoom  
¡OTR (One Touch Recording)  
¡Marker  
Allows you to assign a specific point on a disc to be called  
back later.  
¡Resume Play  
PRECAUTIONS  
AVOID THE HAZARDS OF  
INSTALLATION LOCATION  
ELECTRICAL SHOCK AND FIRE  
For safety and optimum performance of your  
DVD/VCR COMBINATION UNIT:  
• Do not handle the power cord with wet hands.  
• Do not pull on the power cord when disconnecting it  
from AC wall outlet. Grasp it by the plug.  
• If, by accident, water is spilled on your DVD/VCR  
COMBINATION UNIT, unplug the power cord imme-  
diately and take the unit to our Authorized Service  
Center for servicing.  
• Install the DVD/VCR COMBINATION UNIT in a hor-  
izontal and stable position. Do not place anything  
directly on top of the DVD/VCR COMBINATION  
UNIT. Do not place the DVD/VCR COMBINATION  
UNIT directly on top of the TV.  
• Shield it from direct sunlight and keep it away from  
sources of intense heat. Avoid dusty or humid  
places. Avoid places with insufficient ventilation for  
proper heat dissipation. Do not block the ventilation  
holes on the sides of the DVD/VCR COMBINATION  
UNIT. Avoid locations subject to strong vibration or  
strong magnetic fields.  
• Do not put your fingers or objects into the DVD/VCR  
COMBINATION UNIT cassette holder.  
MOISTURE CONDENSATION WARNING  
Moisture condensation may occur inside the unit when  
it is moved from a cold place to a warm place, or after  
heating a cold room or under conditions of high  
humidity. Do not use the DVD/VCR COMBINATION  
UNIT at least for 2 hours until its inside is dry.  
EN  
Download from Www.Somanuals.com6. All Manuals Search And Download.  
1L25  
ABOUT THE DISCS  
PLAYABLE DISCS  
DISC TYPES  
The following discs can be played back on this  
DVD/VCR COMBINATION UNIT.  
[
]
DVD  
Data on a DVD is divided into sections called "titles", and  
then into subsections called "chapters", each of which is  
given a title or chapter number. Playback conditions are  
preset on some DVD video discs, and these playback con-  
ditions take priority over user operations on this player. If  
a function you selected does not run as desired, refer to  
the manual accompanying the disc.  
¡
¡
¡
¡
¡
¡
DVD video  
DVD-R/RW* (video format)  
DVD+R/RW* (video format)  
Audio CD  
CD-R/RW* (audio CD format)  
Example  
Audio CD with MP3 files*  
* Depending on the types or the writing method of the  
medium some discs can not be played.  
Title 1  
Title 2  
Chapter 1 Chapter 2 Chapter 3 Chapter 4 Chapter 1 Chapter 2  
¡Some DVD-R/RW, DVD+R/RW, or CD-R/RW discs  
made on personal computers, or on DVD recorders may  
not be played back properly due to factors such as  
scratches, dirt or special properties of the disc.  
¡Discs made on personal computers may not be played  
back properly due to different environments or the set-  
tings of the application you use. We recommend always  
to use the standardized, properly formatted discs.  
(Please contact the sales agency for more detail).  
[
]
AUDIO CD  
Data on an audio CD is divided into sections called  
“tracks”, each of which is given a track number.  
Example  
This player conforms to the NTSC color system. You can-  
not play discs recorded in other color systems such as  
PAL or SECAM.  
Track 1  
Track 2  
Track 3  
Track 4  
Track 5  
Track 6  
¡Some discs include region codes as shown below.  
[Audio CD with  
]
MP3 files  
MP3 data is divided into sections called "groups", and  
then into subsections called "tracks", each of which is  
given a group or track number.  
¡The number inside the symbol refers to a region of the  
world, and a disc encoded in a specific region format  
can only be played back on DVD/VCR COMBINA-  
TION UNIT with the same region code.  
The following discs cannot be played back on this  
DVD/VCR COMBINATION UNIT.  
Example  
Group 1  
Group 2  
¡
¡
¡
DVD with region codes other than 1 or ALL.  
Track 1  
Track 2  
Track 3  
Track 4  
Track 1  
Track 2  
DVD-ROM for personal compurters.  
DVD-RAM (Never play back, otherwise malfunc-  
tion may result.)  
¡
¡
¡
¡
¡
CD-ROM for personal computers.  
VSD  
CDV (Only plays back the audio part.)  
CD-G (Only plays back the sound.)  
CD-I (Never play back, otherwise malfunction  
may result.)  
¡
SACD  
¡
Photo CD (Never play back, otherwise malfunc-  
tion may result.)  
¡
Video CD (Never play back, otherwise malfunc-  
tion may result.)  
Any other discs without compatibility indications.  
EN  
Download from Www.Somanuals.com7. All Manuals Search And Download.  
1L25  
OPERATING CONTROLS AND FUNCTIONS  
FRONT PANEL  
1
2
3
4
5
6 7  
8
POWER  
OPEN/CLOSE  
CH-UP  
STOP/EJECT  
FF  
OUTPUT  
DVD  
STOP  
FWD  
REW  
REV  
PLAY  
VCR  
REC  
TIMER  
REC  
VIDEO  
AUDIO  
PLAY  
DISC IN  
CH-DOWN  
PLAY  
25  
24 23 22  
20  
18 16 14 12  
17  
10  
21  
19  
15  
13  
11  
9
REMOTE CONTROL  
6. POWER Button [page 16]  
Press to turn the power on and off.  
7. POWER Light (red)  
55  
26  
POWER SPEED AUDIO  
Light appears when the power is on.  
8. STOP/EJECT Button (VCR)  
EJECT  
27  
1
4
7
2
5
8
0
3
54  
52  
SKIP/CH.  
Press to remove the tape from the VCR.  
STOP  
6
28  
VCR/TV  
SLOW  
Press to stop the tape motion.  
9. PLAY Button(VCR) [page 18]  
Press to begin playback.  
9
53  
+
10  
DISPLAY DVD  
VCR  
PAUSE  
10. CH-(UP/DOWN) Buttons [page 16]  
51  
49  
29  
31  
33  
In VCR mode, press to change TV channels on the  
VCR; press to adjust the tracking during normal or  
slow motion playback; press to remove vertical jitter  
in a Still picture.  
50  
48  
30  
32  
PLAY  
STOP  
11. AUDIO In Jack [page 21]  
RECORD  
MENU  
Connect an audio cable coming from the audio out  
jack of a camcorder, another VCR, or an audio source  
here.  
47  
45  
34  
36  
38  
ENTER  
46  
35  
37  
SETUP  
TITLE  
RETURN  
12. VIDEO In Jack [page 21]  
SEARCH  
MODE  
CLEAR/  
MODE ZOOM  
Connect a video cable coming from the video out  
jack of a camcorder, another VCR, or a video source  
(laser disc player, camcorder, etc.) here.  
13. FF Button (VCR) [page 18]  
C.RESET  
44  
42  
43  
41  
SUBTITLE ANGLE REPEAT  
A
B
39  
T-SET  
40  
Press to rapidly advance the tape, or view the picture  
rapidly in forward during playback. (Forward  
Search).  
14. REW Button (VCR) [page 18]  
Press to rewind the tape, or to view the picture rapid-  
ly in reverse during the playback mode (Rewind  
Search).  
1. Disc loading tray  
2. OPEN/CLOSE Button [page 22]  
Press to insert discs into or remove them from the  
tray.  
15. REC Button [page 19]  
3. DVD OUTPUT Light (Green) [page 12]  
This light appears when the DVD output mode is  
selected. You can only watch DVDs when the green  
DVD OUTPUT light is on. To make the green DVD  
OUTPUT light come on, press DVD on the remote  
control or OUTPUT on the front panel.  
Press once to start a recording. Press repeatedly to  
start a One-Touch Recording.  
16. REC Light [page 19]  
Light appears during recording.  
17. TIMER Light [page 19]  
Light appears when the DVD/VCR is in standby  
mode for a timer recording or during a One-Touch  
Recording. It flashes if T-SET is pressed for a timer  
recording, but there is no tape in the DVD/VCR. It  
flashes when all timer recordings or One-Touch  
Recordings are finished.  
4. VCR OUTPUT Light (Green) [page 12]  
This light appears when the VCR output mode is  
selected. You can only watch tapes when the green  
VCR OUTPUT light is on. To make the green VCR  
OUTPUT light come on, VCR on the remote control  
or OUTPUT on the front panel.  
5. CASSETTE COMPARTMENT  
EN  
Download from Www.Somanuals.com8. All Manuals Search And Download.  
1L25  
18. OUTPUT Button [page 12]  
Press to select DVD mode or VCR mode.  
You can switch the output mode either by pressing  
OUTPUT on the front panel, or by pressing DVD  
or VCR on the remote control. However, if you  
press OUTPUT on the front panel first, you  
need to re-select the corresponding mode by  
pressing DVD or VCR on the remote control.  
19. Remote Sensor Window  
31. h Button  
DVD mode [page 23]  
Press to view the DVD picture in fast reverse motion.  
Press PAUSE, then press this button to begin slow  
motion playback.  
VCR mode [page 18]  
Press to rewind the tape, or to view the picture rapidly  
in reverse during the playback mode (Rewind Search).  
32. STOP Button  
20. DISC IN Light (green)  
DVD mode  
Light appears when a disc is in the DVD Player.  
21. PLAY Light (green)  
Press to stop the disc motion.  
VCR mode  
Light appears during Disc playback.  
22. FWD Button (DVD) [page 23]  
Press this button during playback to fast forward the  
Disc. Press this button in PAUSE mode to slow for-  
ward the Disc.  
Press to stop the tape motion.  
33. RECORD Button [page 19]  
Press once to start a recording.  
34. MENU Button  
DVD mode [page 23]  
Press to skip Chapters or Tracks.  
Press to display the menu of the Disc.  
VCR mode [page 17]  
23. PLAY Button (DVD) [page 22]  
Press to begin playback.  
Press to access the VCR menu.  
35. TITLE Button [page 23]  
36. SETUP Button [pages 28-31]  
Press to enter DVD player setup mode.  
37. ZOOM Button [page 24]  
Enlarges part of a DVD-reproduced image.  
38. MODE Button [pages 26, 27, and 30]  
Activates program playback or random playback  
mode when playing CDs or MP3. Sets Black level  
and virtual surround.  
24. REV Button (DVD) [page 23]  
Press this button during playback to fast reverse the  
Disc. Press this button in PAUSE mode to slow  
reverse the Disc.  
Press to skip Chapters or Tracks.  
25. STOP Button (DVD) [page 22]  
Stops operation of the disc.  
26. SPEED Button [page 19]  
Press to select the VCR’s recording speed (SP or  
SLP)  
39. SUBTITLE Button [page 27]  
Press to select the desired subtitle language.  
39. T-SET Button [page 20]  
Press to put the VCR into standby mode for a timer  
recording.  
40. ANGLE Button [page 27]  
Press to change the camera angle to see the sequence  
being played back from a different angle.  
41. REPEAT Button [page 25]  
Repeats playback of the current disc, title, chapter or  
track.  
27. POWER Button  
Press to turn the power on and off.  
28. Number Buttons  
DVD mode [page 24]  
Press to select numbered items in a menu.  
+10  
Use this button to enter number 10 and above.  
VCR mode [page 16]  
Press to select TV channels on the VCR.  
To select channels, enter channel numbers as a  
two-digit number for the quickest results. For  
example, to select channel 6, press 0 then 6.  
29. DISPLAY Button  
42. A-B REPEAT Button [page 25]  
Repeats playback of a selected section.  
43. SEARCH MODE Button  
DVD mode [page 24]  
DVD mode [page 28]  
Press to access or remove the display screen during  
DVD or Audio CD playback.  
VCR mode [page 21]  
Press to access or remove the VCR’s on-screen sta-  
tus display.  
Press to access or remove the Search display,  
which allows you to go directly to a specific  
Title/Chapter/Track/Time.  
VCR mode [page 18]  
Press to perform a Time Search or an Index Search.  
44. CLEAR/C.RESET Button  
DVD mode [pages 24, 25]  
Press to reset the setting.  
30. DVD Button [page 12]  
Press to select DVD mode for the remote control.  
You can switch the OUTPUT mode either by  
pressing OUTPUT on the front panel, or by press-  
ing DVD or VCR on the remote control. However,  
if you press OUTPUT on the front panel first,  
you need to re-select the corresponding mode by  
pressing DVD or VCR on the remote control.  
VCR mode [page 18]  
Press to reset the counter. Press to exit from the  
MENU screen.  
45. RETURN Button [page 30]  
DVD mode  
Returns to the previous operation in the DVD  
setup mode.  
EN  
Download from Www.Somanuals.com9. All Manuals Search And Download.  
1L25  
46. Arrow Buttons  
51. PAUSE Button  
Use when making settings while watching the dis-  
play on a TV screen.  
DVD mode [page 22]  
Press to pause Disc playback. Press repeatedly to  
advance the DVD picture step by step (or one  
frame at a time).  
VCR mode [page 16]  
p/o Buttons  
Press to enter digits when setting program (For  
example: setting clock or timer program). Press to  
select the setting modes from the on screen menu.  
B Button  
When setting program (For example: setting clock  
or timer program), press to determine your selec-  
tion and proceed to the next step you want to  
VCR mode [page 19]  
While recording, press to temporarily stop the  
recording (pause). Press a second time to resume  
normal recording. You can not pause a One-Touch  
Recording. Or, press during tape playback to  
freeze the picture. Press to advance the picture one  
frame at a time during still mode.  
input. Press to determine the setting modes from 52. SLOW Button [page 18]  
the on screen menu. Press to add or delete channel  
numbers during channel preset.  
s Button  
During tape playback, press to view the video tape in  
slow motion. Press again to resume normal playback.  
This button does not affect DVD playback.  
Press to cancel a setting of timer program. Press to 53. VCR/TV Button [page 19]  
correct digits when setting program (For example:  
setting clock or timer program). Press to add or  
delete channel numbers during channel preset.  
Use to select VCR or TV position.  
VCR Position  
To view playback, to monitor video recordings or  
to watch TV using the VCR tuner.  
TV Position  
47. ENTER Button  
DVD mode [page 22]  
Press to accept a setting.  
To watch TV or to view one program while record-  
ing another.  
48. g Button  
DVD mode [page 23]  
54. SKIP/CH. Buttons  
Press to fast forward the Disc. Press PAUSE, then  
press this button to begin slow motion playback.  
VCR mode [page 18]  
DVD mode  
Press to skip Chapters or Tracks.  
VCR mode  
Press to rapidly advance the tape, or view the pic-  
Press to change TV channels on the VCR.  
ture rapidly in forward during playback (Forward 55. AUDIO Button [page 27]  
Search).  
Press to select a desired audio language or sound  
mode.  
49. PLAY Button  
DVD mode  
Press to begin playback.  
VCR mode  
Notes  
Press to begin playback.  
¡To use the remote control to operate the DVD/VCR  
COMBINATION UNIT and its features, press DVD on  
the remote control before pressing other DVD’s opera-  
tion buttons. Verify that the green DVD OUTPUT  
Light is on.  
50. VCR Button [page 12]  
Press to select VCR mode for the remote control.  
You can switch the OUTPUT mode either by  
pressing OUTPUT on the front panel, or by press-  
ing DVD or VCR on the remote control. However,  
if you press OUTPUT on the front panel first,  
you need to re-select the corresponding mode by  
pressing DVD or VCR on the remote control.  
¡To use the remote control to operate the VCR and its  
features, press VCR on the remote control before  
pressing other VCR’s operation buttons. Verify that the  
green VCR OUTPUT Light is on.  
EN  
10  
 
1L25  
REAR VIEW  
56 57  
58  
59  
60  
DVD  
DVD/VCR  
VCR  
AUDIO OUT  
S-VIDEO COMPONENT AUDIO  
DIGITAL  
AUDIO OUT  
OUT  
VIDEO OUT  
OUT  
ANT-IN  
L
Y
AUDIO IN  
Cb  
Cr  
L
R
COAXIAL  
ANT-OUT  
VIDEO OUT  
VIDEO IN  
R
66  
64  
62  
65  
63  
61  
56. ANT-IN (Antenna In) Jack  
Connect your antenna, Cable Box, or Satellite decoder  
box.  
62. DVD ANALOG AUDIO OUT Jacks  
Connect the supplied audio cables here and to the  
Audio In jacks of a television or other audio equip-  
ment (DVD only).  
57. DVD/VCR AUDIO OUT Jacks  
Connect the supplied audio cables here and to the 63. S-VIDEO OUT Jack  
Audio In jacks of a television or other audio equip-  
ment.  
Connect an optional S-Video cable here and to the S-  
Video In jack of a television. (DVD only).  
64. VIDEO IN Jack  
58. AUDIO IN Jack  
Connect an audio cable coming from the audio out  
jack of a camcorder, another VCR, or an audio  
source here.  
Connect a cable coming from the video out jack of a  
camcorder, another VCR, or an audio-visual source  
(laser disc player, video disc player, etc.) here.  
65. DVD/VCR VIDEO OUT Jack  
59. AC Power Cord  
Connect to a standard AC outlet to supply power to  
the DVD/VCR COMBINATION UNIT.  
Connect the yellow video cable (supplied) here and  
to the TV’s Video In jack.  
66. ANT-OUT (Antenna Out) Jack  
Use the supplied RF cable to connect this jack to the  
ANTENNA IN Jack on your TV.  
DVD Playback only  
60. COMPONENT VIDEO OUT Jacks  
Connect optional component video cables here and  
to the component Video In jacks of a television.  
61. COAXIAL Jack  
Note  
¡The S-VIDEO OUT jack, COAXIAL jack, and COM  
PONENT VIDEO OUT jack are only useful in DVD  
mode.  
Caution: Do not touch the inner pins of the jacks  
on the rear panel. Electrostatic discharge may  
cause permanent damage to the player.  
Connect an optional coaxial digital audio cable here  
and to the Coaxial Digital Audio In jack of a decoder  
or audio receiver.  
LOADING THE BATTERIES  
1. Open the battery compartment cover.  
2. Insert two AA batteries (supplied), with each one oriented correctly.  
3. Close the cover.  
Notes  
¡Do not mix alkaline and manganese batteries.  
¡Do not mix old and new batteries.  
EN  
11  
 
1L25  
VCR/DVD SWITCHING  
Because this product is a combination of a VCR and DVD player, you must first select  
which component you wish to operate with the OUTPUT BUTTON.  
VCR MODE  
DVD MODE  
Press VCR on the remote control.  
(Verify that the VCR OUTPUT Light is lit.)  
Press DVD on the remote control.  
(Verify that the DVD OUTPUT Light is lit.)  
Note  
¡Pressing only OUTPUT on the front panel does not switch the mode of the remote control. You always need  
to select the correct mode on the remote control too.  
POWER  
OPEN/CLOSE  
POWER SPEED AUDIO  
CH-UP  
STOP/EJECT  
FF  
OUTPUT  
STOP  
FWD  
DVD  
REW  
REV  
PLAY  
VCR  
REC  
TIMER  
REC  
VIDEO  
AUDIO  
PLAY  
DISC IN  
CH-DOWN  
PLAY  
1
4
7
2
5
8
0
3
SKIP/CH.  
6
VCR/TV  
SLOW  
9
DVD OUTPUT Light  
+
10  
DVD button  
VCR button  
DISPLAY DVD  
VCR  
PAUSE  
PLAY  
STOP  
OUTPUT  
DVD  
VCR  
RECORD  
MENU  
VCR OUTPUT Light  
ENTER  
SETUP  
TITLE  
RETURN  
SEARCH  
MODE  
CLEAR/  
MODE ZOOM  
C.RESET  
OUTPUT button  
SUBTITLE ANGLE REPEAT  
A
B
T-SET  
EN  
12  
 
1L25  
HOOKUPS  
CAUTION:  
¡Be sure to turn off the DVD/VCR COMBINATION UNIT and equipment to be connected.  
¡Read through the operation manual for the equipment to be connected.  
¡Be sure that the colors of the jacks and plugs match up when using VIDEO/AUDIO cables.  
¡Be sure to keep the DVD/VCR COMBINATION UNIT connection cables separate from the TV antenna cable  
when you install the DVD/VCR COMBINATION UNIT, because it may cause electrical interference when you  
are watching television programs.  
CONNECTING TO A TV WITHOUT A/V TERMINALS  
1. Disconnect the AC power cord of the TV from the  
[VHF/UHF  
[Back of the DVD/VCR]  
[Indoor antenna]  
AC outlet.  
combination antenna]  
[Back of the  
2. Disconnect the antenna or cable from the TV.  
3. Connect the antenna or cable to the ANT-IN jack of  
the DVD/VCR COMBINATION UNIT.  
4. Connect the DVD/VCR COMBINATION UNIT to  
the TV using the RF cable.  
5. Plug the AC power cords of the DVD/VCR COM-  
BINATION UNIT and TV into the AC outlets.  
UHF/VHF combination TV]  
DVD/VCR  
VCR  
RF cable  
(supplied)  
OR  
OR  
AUDIO OUT  
ANT-IN  
L
UHF/VHF  
[Cable box or satellite box]  
AUDIO IN  
R
IN  
ANT-OUT  
VIDEO OUT  
OUT  
VIDEO IN  
From Cable or  
Satellite Company  
RF OUTPUT CHANNEL for DVD/VCR  
1. Connect the DVD/VCR COMBINATION UNIT to a TV using RF cable (see above steps).  
2. Select channel 3 on your TV.  
3. Press PLAY.  
¡If noise appears, change the RF output channel of the DVD/VCR COMBINATION UNIT to channel 4 by  
pressing PLAY on the VCR for 3 seconds during playback.  
¡There is case that the RF output channel does not change by situation (For example, when you adjust track-  
ing using SKIP/CH. (o/p) on the remote or CH-(UP/DOWN) on the DVD/VCR COMBINATION UNIT).  
In this case, stop the playback, and start the playback again. After that, press PLAY on the VCR for 3 sec-  
onds.  
¡If there is a power failure or the DVD/VCR COMBINATION UNIT is unplugged for more than 30 seconds,  
the RF output channel setting will return to CH3.  
Note to CATV system installer  
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that pro-  
vides guidelines for proper grounding and, in particular, specifies that the cable ground should be connected  
to the grounding system of the building, as close to the point of cable entry as practical.  
CONNECTING TO A TV WITH A/V TERMINALS  
DVD  
DVD/VCR  
VCR  
AUDIO OUT  
S-VIDEO COMPONENT AUDIO  
DIGITAL  
AUDIO OUT  
OUT  
VIDEO OUT  
OUT  
Antenna/Cable signal  
A/V-compatible or  
ANT-IN  
L
Y
DIO IN  
Cb  
Cr  
L
R
COAXIAL  
ANT-OUT  
VIDEO OUT  
VIDEO IN  
R
wide screen TV  
To ANT. IN  
of TV  
To VIDEO INPUT jack  
To VIDEO OUT jack  
To Right (red) and Left (white)  
To AUDIO INPUT jacks  
[Fig. 1]  
To AUDIO OUT jacks  
Note  
¡Connect the DVD/VCR COMBINATION UNIT directly to a TV. If the A/V cables are connected into a  
VCR first, pictures may be distorted due to the copy protection system.  
EN  
13  
 
1L25  
CONNECTING TO A TV THAT HAS AN S-VIDEO INPUT JACK OR  
COMPONENT VIDEO IN JACKS  
FOR TVs WITH S-VIDEO INPUT JACK  
Use an S-Video cable (commercially available) in place of the yellow video cable to enjoy higher quality pic-  
tures.  
The S-Video connection only supplies video (picture) in the DVD mode of the DVD/VCR COMBINATION  
UNIT. Therefore, in order to use the VCR features or view TV channels on the DVD/VCR COMBINATION  
UNIT, you still need to either connect the RF cable between the ANT-OUT jack of the DVD/VCR COMBINA-  
TION UNIT and the TV’s Antenna In jack, or connect the yellow video cable as described earlier (Fig.1). To  
connect the supplied RF cable, see page 13.  
DVD  
DVD/VCR  
VCR  
AUDIO OUT  
S-VIDEO COMPONENT AUDIO  
DIGITAL  
AUDIO OUT  
OUT  
VIDEO OUT  
OUT  
ANT-IN  
L
Y
A/V-compatible or  
wide screen TV  
AUDIO IN  
Cb  
Cr  
L
R
COAXIAL  
ANT-OUT  
VIDEO OUT  
VIDEO IN  
R
To S-VIDEO INPUT jack  
To S-VIDEO OUT jack  
To Right (red) and Left (white)  
To AUDIO INPUT jacks  
[Fig. 2]  
To AUDIO OUT jacks  
FOR TVs WITH  
COMPONENT VIDEO IN JACKS  
Use a component video cable (commercially available) in place of the yellow DVD/VCR video cable and S-VIDEO  
jack to enjoy higher quality pictures.  
The component video connection only supplies video (picture) in the DVD mode of the DVD/VCR COMBINATION  
UNIT. Therefore, in order to use the VCR features or view TV channels at the DVD/VCR COMBINATION UNIT,  
you still need to either connect the RF cable between the ANT-OUT jack of the DVD/VCR COMBINATION UNIT  
and the TV’s Antenna In jack, or connect the yellow VCR video cable as described earlier (Fig. 1). To connect the sup-  
plied RF cable, see page 13.  
To Right (red) and Left (white)  
AUDIO OUTPUT jacks  
To Right (red) and Left (white)  
AUDIO INPUT jacks  
A/V-compatible  
or  
wide screen TV  
DVD  
DVD/VCR  
VCR  
AUDIO OUT  
S-VIDEO COMPONENT AUDIO  
DIGITAL  
OUT  
VIDEO OUT  
OUT  
AUDIO OUT  
ANT-IN  
L
Y
AUDIO IN  
Cb  
Cr  
L
R
COAXIAL  
ANT-OUT  
VIDEO OUT  
VIDEO IN  
R
[Fig. 3]  
To COMPONENT VIDEO  
INPUT jacks  
To COMPONENT VIDEO  
OUT jacks  
CONNECTING TO A STEREO AMPLIFIER EQUIPPED WITH  
DIGITAL INPUT JACKS SUCH AS MD DECK OR DAT DECK  
Use an audio coaxial digital cable (commercially available) for the audio connections.  
Connecting to an amplifier equipped with digital input jacks such as MD Deck or DAT Deck.  
DVD  
DVD/VCR  
VCR  
AUDIO OUT  
S-VIDEO COMPONENT AUDIO  
DIGITAL  
AUDIO OUT  
(Stereo Receiver)  
Amplifier equipped with digital  
input jacks, MD deck,  
DAT deck, etc.  
OUT  
VIDEO OUT  
OUT  
ANT-IN  
L
Y
AUDIO IN  
Cb  
Cr  
L
R
COAXIAL  
ANT-OUT  
VIDEO OUT  
VIDEO IN  
R
To COAXIAL DIGITAL  
AUDIO OUT jack  
[Fig. 4]  
To COAXIAL DIGITAL AUDIO INPUT jack  
Notes  
¡The audio source on a disc in the 5.1 channel Dolby Digital surround format cannot be recorded as digital  
sound by an MD or DAT deck.  
¡Set DOLBY DIGITAL to OFF for audio output in the setup mode. Playing a DVD disc using incorrect set-  
tings may generate noise distortion, and may also damage the speakers. (See page 29 to set DOLBY DIGITAL  
to OFF)  
EN  
14  
 
1L25  
CONNECTING TO A RECEIVER WITH DOLBY DIGITAL DECODER  
If using this DVD/VCR COMBINATION UNIT to play a DVD disc in 5.1 channel Dolby Digital surround, the  
DVD/VCR COMBINATION UNIT outputs a Dolby Digital data stream from its COAXIAL DIGITAL AUDIO  
OUT jack. By hooking the DVD/VCR COMBINATION UNIT up to a Dolby Digital receiver, you can enjoy a  
more convincing, realistic ambience with powerful and high-quality surround sound as heard in movie theaters.  
Use an audio coaxial digital cable (commercially available) for the audio connections.  
DVD  
DVD/VCR  
VCR  
AUDIO OUT  
S-VIDEO COMPONENT AUDIO  
DIGITAL  
AUDIO OUT  
OUT  
VIDEO OUT  
OUT  
ANT-IN  
L
Y
AUDIO IN  
Cb  
Cr  
L
R
COAXIAL  
ANT-OUT  
VIDEO OUT  
VIDEO IN  
R
Center speaker  
Front speaker  
(right)  
Front speaker  
(left)  
To COAXIAL DIGITAL  
AUDIO OUT jack  
Receiver with  
Dolby Digital Decoder  
To COAXIAL DIGITAL  
AUDIO INPUT jack  
Subwoofer  
Surround  
speaker  
(left)  
Surround  
speaker  
(right)  
[Fig. 5]  
¡If the output is Dolby Digital audio, connect to a Dolby Digital decoder, and set DOLBY DIGITAL to ON for  
audio output in the setup mode.  
¡Unless connected to a Dolby Digital receiver, set DOLBY DIGITAL to OFF for audio output in the setup mode.  
Playing a DVD using incorrect settings may generate noise distortion, and may also damage the speakers.  
Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of  
Dolby Laboratories.  
CONNECTING TO AN ANALOG AUDIO SYSTEM  
DVD  
DVD/VCR  
VCR  
AUDIO OUT  
S-VIDEO COMPONENT AUDIO  
DIGITAL  
AUDIO OUT  
OUT  
VIDEO OUT  
OUT  
ANT-IN  
L
Y
IN  
Cb  
Cr  
L
R
COAXIAL  
ANT-OUT  
VIDEO OUT  
VIDEO IN  
R
Stereo system  
To Right (red) and Left (white)  
AUDIO INPUT jacks  
or  
To ANALOG AUDIO INPUT jacks  
[Fig. 6]  
To Right (red) and Left (white)  
ANALOG AUDIO OUT jacks  
Notes  
¡Be sure to turn off the power to all components in the system before connecting another component.  
¡Refer to the Owner's Manuals for stereo systems and any other components to be connected to the DVD/VCR  
COMBINATION UNIT.  
EN  
15  
 
1L25  
SETUP  
AUTOMATIC CHANNEL SET UP  
5 Begin channel preset by pressing B once.  
The tuner scans and memo-  
rizes all active channels in  
your area.  
CH 01  
VCR  
AUTO SET UP  
You can automatically program the tuner to scan only  
the channels you receive in your area.  
¡The VCR distinguishes between  
standard TV channels and cable  
channels.  
¡Channel memory programming is NOT needed  
when you connect the VCR to a cable box or a satel-  
lite box as in "CONNECTING TO A TV WITHOUT  
A/V TERMINALS" on page 13. In this case, select  
channel 3 on your TV. Then, the channel you want to  
record or view may be selected at the cable box or  
satellite box.  
¡If noise appears, change the RF output channel of  
the VCR to channel 4 by pressing PLAY for 3 sec-  
onds during playback. Then select the same chan-  
nel (CH4) on your TV.  
¡Follow the steps below once. Repeat only if there is  
a power failure or if the VCR is unplugged for more  
than 30 seconds. (In these cases, the programmed  
channels are erased.)  
¡You must follow the steps below before attempting  
to play or record a video tape. If you want to play  
or record a video tape BEFORE programming the  
tuner, you can cancel it by pressing  
6
After scanning, the tuner stops on the low-  
est memorized channel. The TV screen  
returns to TV mode.  
¡If “AUTO SET UP” appears on the TV screen again,  
check the cable connections. Press B once again and  
the VCR will begin preset again.  
TO SELECT A DESIRED CHANNEL  
You can select the desired channel by using SKIP/CH.  
(o/p) or by directly pressing the Number buttons on  
the remote control.  
Note for using the Number buttons:  
¡When selecting cable channels which are higher  
than 99, enter channel numbers as a three-digit num-  
ber.(For example: 117, press 1,1,7)  
¡You must precede single-digit channel numbers with  
a zero (For example: 02, 03, 04 and so on).  
CLEAR/C.RESET.  
TO PRESET THE CHANNELS AGAIN  
1
You need to connect the antenna or cable to  
the VCR first. Then, connect the DVD /VCR  
power plug to a standard AC outlet.  
1
Press MENU until the main menu appears.  
(If you have already set the clock, you only  
have to press it once. If not, you have to  
press it twice).  
2
Turn on the TV and set the TV to channel 3.  
¡If noise appears, change the RF output channel of  
the VCR to channel 4 by pressing PLAY for 3 sec-  
onds during playback. Then select the same channel  
(CH4) on your TV. (See “RF OUTPUT  
CHANNEL” on page 13 for the detail.)  
2
3
Select “CHANNEL SET UP” by pressing  
or L. Then, press B.  
K
Select “AUTO SET UP” by pressing K or L.  
Then, press B.  
3
4
Turn on the VCR by pressing POWER. the  
POWER light will come on.  
¡After scanning, the tuner stops on the lowest memo-  
rized channel.  
Select the On Screen Language (“ENG-  
LISH”, “FRANCAIS” or “ESPAÑOL) by  
pressing K or L. Then,  
press B.  
EN  
16  
 
1L25  
TO ADD/DELETE CHANNELS  
CLOCK SET UP  
When scanning, some channels may be skipped due to  
a weak signal. In such cases, you can add the channels  
to the VCR memory manually.  
VCR  
1
Select main menu by pressing MENU.  
1
Press MENU until the main menu appears.  
¡If the clock is not set, the CLOCK SET menu  
appears first. In this case, follow step [3].  
(If you have already set the  
- MENU -  
TIMER PROGRAMMING  
[OFF]  
AUTO REPEAT  
CHANNEL SET UP  
CLOCK SET  
clock, you only have to  
press it once. If not you  
have to press it twice).  
LANGUAGE SELECT  
AUDIO OUT  
[ON]  
TV STEREO  
SAP  
2
3
Select "CLOCK SET" by pressing K or L.  
Then, press B.  
Set the clock.  
2
3
4
5
Select "CHANNEL SET UP" by pressing  
K
or L. Then, press B.  
1) Set the month  
Select "MANUAL SET UP" by pressing K or  
L. Then, press B.  
Press K or L repeatedly.  
Then, press B.  
Enter the desired channel number by press-  
ing K or L.  
2) Set the day  
Press K or L repeatedly.  
Then, press B.  
Add or Delete it from memory by pressing  
B or s so that "ADD" or "DELETE" flashes  
on the TV screen accordingly.  
3) Set the year  
Press K or L repeatedly.  
Then, press B.  
The day of the week will appear automatically.  
6
Exit the Preset mode by pressing  
CLEAR/C.RESET.  
4) Set the hour  
Press K or L repeatedly.  
Then, press B.  
TO CHANGE THE ON-SCREEN  
LANGUAGE  
5) Set the minute  
Press K or L repeatedly.  
Then, press B.  
VCR  
1
Press MENU twice to call up the main  
menu. (If you have already set the clock,  
you only have to press it once).  
6) Set AM or PM  
CLOCK SET  
MONTH DAY  
YEAR  
Press K or L repeatedly.  
03 17 MON 2003  
/
HOUR MINUTE AM/PM  
05  
:
40  
PM AM  
PM  
2
3
Select "LANGUAGE SELECT" by pressing  
or L. Then, press B.  
K
¡To go back one step, press s.  
Select "ENGLISH", "FRANCAIS" or  
"ESPAÑOL" by pressing K or L. Then, press  
CLEAR/C.RESET.  
4
Start the clock by pressing  
CLEAR/C.RESET or B.  
¡If you accidentally select Spanish or French and  
need English: Press MENU and choose SELEC.  
IDIOMA, or SELECTION LANGUE. Press B,  
and select ENGLISH by pressing K or L.  
Finally, press CLEAR/C.RESET.  
EN  
17  
 
1L25  
PLAYBACK FUNCTION  
NORMAL PLAYBACK  
2
3
Select "AUTO REPEAT" by pressing K or L.  
VCR  
Begin auto repeat playback by pressing  
so that ON appears next to "AUTO  
REPEAT".  
B
1
Insert a prerecorded tape. The VCR will turn  
on.  
¡If the safety tab has been removed, the  
VCR will start playback automatically.  
¡
If the on-screen menu still remains, press  
CLEAR/C.RESET to exit the menu.  
¡To cancel the Auto repeat mode, press B at step [3]  
so that OFF appears next to "AUTO REPEAT".  
2
Turn on the TV and set the TV to channel 3.  
¡If noise appears, change the RF output channel of  
the VCR to channel 4 by pressing PLAY for 3 sec-  
onds during playback. Then select the same channel  
(CH4) on your TV. (See “RF OUTPUT  
CHANNEL” on page 13 for the detail.)  
SEARCH FUNCTIONS  
VCR  
PICTURE SEARCH  
3
Begin playback by pressing PLAY.  
If you want to skip or repeat a scene during playback,  
press D or E.  
¡Tracking adjustment will be done automatically  
(Digital Tracking function) when you start playback.  
To adjust the tracking manually, press SKIP/CH.  
(o/p) on the remote or CH-(UP/DOWN) on the  
VCR.  
¡Press it again and the VCR will now search at super  
high speed. (in the LP/SLP modes only).  
INDEX SEARCH  
¡When a tape has reached the end, the VCR will An index mark will be assigned at the beginning of  
rewind the tape to the beginning, and eject the tape. each recording you made. You may skip to a specific  
marked point by following the steps below.  
4
To stop playback, press STOP.  
¡If no corresponding symbols appear on the display  
when you press buttons such as PLAY, RECORD,  
D or E, that means no cassette tape is in the  
VCR. Please insert a tape.  
1
2
Press SEARCH MODE so that the Index  
Search menu appears.  
Enter the number of recordings you wish to  
Counter Reset  
skip by pressing K or  
L
INDEX SEARCH  
03  
¡You can reset the counter by pressing  
CLEAR/C.RESET on the remote control twice.  
within 30 seconds.  
STILL/SLOW  
You can freeze the picture on TV screen by pressing  
PAUSE during playback.  
3
Press B or { to start index search.  
¡If you want to go in the forward direction, press B.  
¡If you want to go in the reverse direction, press {.  
¡If you want to stop search function, press STOP.  
¡After index search, the VCR will play the tape auto-  
matically.  
¡You can advance the picture one frame at a time by  
pressing PAUSE during the Still mode.  
¡You cannot manually adjust the tracking of a still  
picture. However, if the picture begins to vibrate  
vertically during the still mode, you can stabilize the  
picture by pressing SKIP/CH. (o/p) on the remote  
or CH-(UP/DOWN) on the VCR.  
¡If the picture is distorted or rolling vertically, adjust  
the vertical hold control on your TV, if so equipped.  
¡You can watch in the slow motion by pressing  
SLOW during playback or the still mode.  
TIME SEARCH  
This feature allows you to go to a specific point on a  
tape by entering the exact amount of time you wish to  
skip in order to reach the point.  
1
2
Press SEARCH MODE 2 times so that the  
Time Search menu appears.  
¡If a noise bar appears on the TV screen, you can  
reduce it by pressing SKIP/CH. (o/p) on the  
remote or CH-(UP/DOWN) on the VCR.  
TIME SEARCH  
2 : 50  
Enter your desired time to  
¡After the VCR has been in Still/Slow mode for 5  
minutes, it will stop automatically to protect the tape  
and the video head from damage.  
skip by pressing K or  
L
within 30 seconds.  
¡To return to playback, press PLAY.  
3
Press B or { to start time search.  
¡If you want to go in the forward direction, press B.  
¡If you want to go in the reverse direction, press {.  
¡If you want to stop search function, press STOP.  
¡After time search, the VCR will play the tape auto-  
matically.  
AUTO REPEAT PLAYBACK  
VCR  
This feature allows you to play a tape over and over.  
1
Select main menu by pressing MENU.  
EN  
18  
 
1L25  
RECORDING FUNCTION  
VCR  
OTR (One Touch Recording)  
You can not copy a DVD to a videotape  
VCR  
It may be UNLAWFUL to record copyrighted materi-  
al without the consent of the copyright owner.  
Accidental Erasure Prevention  
This feature allows you to set the recording length sim-  
ply by pressing REC on the VCR.  
To prevent accidental recording on a  
recorded cassette, remove its record  
1
Press REC to begin OTR. The TIMER light  
comes on. Change the recording length by  
pressing REC repeatedly.  
safety tab. To record on it later, cover the  
hole with cellophane tape.  
Record safety tab  
Before recording, make sure:  
¡The desired channel is selected by pressing the  
Number buttons on the remote control or  
SKIP/CH.(o/p). (If you connected the VCR to a  
cable box or satellite box as in "CONNECTING TO  
A TV WITHOUT A/V TERMINALS" on page 13,  
select channel 3 on your TV, and select the specific  
INPUT channel assigned by your cable box or your  
satellite box on the DVD/VCR COMBINATION  
UNIT. Then, select the channel you want to record  
with the cable box or the satellite box. In this case,  
you can ONLY record and view the SAME channel.)  
¡If noise appears, change the RF output channel of  
the VCR to channel 4 by pressing PLAY for 3 sec-  
onds during playback. Then select the same chan-  
nel (CH4) on your TV.  
REC  
OTR(0:30)  
OTR(1:00).....  
OTR(7:30)  
(Normal recording)  
OTR(8:00)  
¡
If a tape ends during OTR, the VCR will stop, eject  
the tape, and switch to the DVD mode automatically  
as the TIMER REC light blinks. (If the DVD power  
is off, the VCR will become STANDBY status)  
¡When OTR is finished , the VCR turns off automat-  
.
ically.  
To use the VCR again, press T-SET on the remote, or  
STOP/EJECT on the DVD/VCR COMBINATION  
UNIT.  
¡There is a tape with a safety tab in the VCR.  
¡The desired recording speed is selected in SP (stan-  
dard play) or SLP (super long play) mode by press-  
ing SPEED on the remote control.  
TIMER RECORDING  
VCR  
Tape Speed  
Recording/Playback Time  
Type of tape  
SP mode  
SLP mode  
T60  
1 hour  
3 hours  
T120  
2 hours  
6 hours  
T160  
2-2/3 hours  
8 hours  
You may set the VCR to start recording while you are  
away. You can set eight programs to record on specif-  
ic days, daily or weekly within 1 year period.  
NORMAL RECORDING  
If you have not yet set the clock, "CLOCK SET"  
appears. If so, follow the steps [3] and [4] in  
"CLOCK SET UP" section on page 17. Then, set  
the timer recording.  
VCR  
1
Begin the recording by pressing RECORD.  
The REC Light comes on.  
1
Insert a tape with its safety tab into the  
DVD/VCR COMBINATION UNIT.  
¡To temporarily stop recording or to resume it, press  
PAUSE. After the VCR has been in Pause mode for  
5 minutes, it will stop automatically to protect the  
tape and the video head from damage.  
2
3
Select main menu by pressing MENU.  
TIMER PROGRAMMING  
Select "TIMER PROGRAM-  
MING" by pressing K or L.  
Then, press B. The set up  
screen is displayed.  
PROG  
DATE  
12345678  
-
2
Notes  
Press STOP when the recording is completed.  
START TIME  
END TIME  
CHANNEL  
REC SPEED  
¡When you wish to watch another program while  
recording, select desired channel on your TV. If  
noise appears press VCR/TV.  
4
Set the timer.  
¡To go back one step, press s.  
¡This is not possible when using a cable box or  
satellite box.  
1) Set the program number (1-8)  
PROGRAM NUMBER  
4
DATE  
- - / - -  
START TIME - - : - - - -  
END TIME - - : - - - -  
CHANNEL - -  
REC SPEED - -  
Program number which is not set up  
flashes. Press K or L repeatedly  
for the desired program number.  
Then, press B.  
EN  
19  
 
1L25  
¡If a tape ends during TIMER RECORDING, the  
VCR will stop, eject the tape, and switch to the DVD  
mode automatically as the TIMER light blinks. (If  
the DVD power is off, the VCR will become  
STANDBY status).  
¡If a tape is not in the VCR or does not have a safe-  
ty tab, the TIMER light flashes and timer recording  
will not operate. Please insert a recordable tape.  
¡When all timer recordings are finished, the TIMER  
light will flash.  
2) Set the frequency of the recording  
For once: Press K or L to point to  
"ONCE".  
PROGRAM NUMBER  
4
ONCE  
DAILY  
WEEKLY  
For daily (Monday~Friday): Press  
or L to point to "DAILY".  
For weekly: Press K or L to point  
to "WEEKLY".  
K
Then, press B.  
ONE TIME PROGRAM  
PROGRAM NUMBER  
DATE - - / - -  
START TIME - - : - - - -  
END TIME - - : - - - -  
3) Set the date  
4
To use the VCR again as usual, press T-SET to disable the  
flashing TIMER REC light, then press VCR/TV to select the  
VCR position. Select either VCR or DVD mode, then contin-  
First, press K or L for the month.  
Then, press B. Next, press K or  
L for the day. Then, press B.  
CHANNEL  
- -  
REC SPEED - -  
ue with the other features as described in this manual  
.
¡When timer recordings are set, the TIMER light will  
come on. To use the VCR as usual until the time for  
the recording, press T-SET so that TIMER light dis-  
appears. Press VCR/TV to choose the VCR position.  
Select either VCR or DVD mode, then continue with  
the other features as described in this manual.  
ONE TIME PROGRAM  
4) Set the start time  
PROGRAM NUMBER  
DATE 05 /12 MON  
START TIME - - : - - - -  
END TIME - - : - - - -  
CHANNEL - -  
REC SPEED - -  
4
First, press K or L for the hour.  
Then, press B. Next, press K or  
for the minute. Then, press B. And  
then, press K or L for AM or PM. Then, press B.  
L
If you want to use the DVD player during  
a VCR timer recording or while the  
ONE TIME PROGRAM  
PROGRAM NUMBER  
DATE 05 /12 MON  
START TIME 07: 30 PM  
END TIME - - : - - - -  
5) Set the end time  
4
TIMER light is on or flashes.  
Follow the instructions of  
"Set the start time" to set  
the end time.  
¡You can use the DVD player while the TIMER light  
is on or flashes, or during a timer recording. Press  
POWER to turn on the DVD. Press DVD on the  
remote control to choose DVD mode, then continue  
with the other DVD features as described in this  
manual. You don’t have to set the TIMER off to use  
the DVD only.  
CHANNEL  
- -  
REC SPEED - -  
ONE TIME PROGRAM  
6) Set the channel number  
PROGRAM NUMBER  
DATE 05 /12 MON  
START TIME 07: 30 PM  
END TIME 08: 30 PM  
CHANNEL - -  
REC SPEED - -  
4
Press K or L repeatedly for the  
desired channel number. Then,  
press B.  
TO STOP AN AUTOMATIC TIMER PRO-  
GRAM ALREADY STARTED  
Press STOP/EJECT on the DVD /VCR COMBINA-  
TION UNIT.  
If you connected the DVD/VCR COMBINATION UNIT to  
a cable box or satellite box as in "DVD/VCR TO TV  
CONNECTION" on page 13, select the DVD/VCR to channel 3  
or 4 the same channel as RF output channel of the DVD/VCR.  
Then, select the channel you want to record with the cable box  
or satellite box.  
TO CHECK, CORRECT, OR CANCEL AN  
AUTOMATIC TIMER PROGRAM  
Leave the cable box or satellite box on for timer recording.  
ONE TIME PROGRAM  
7) Set the tape speed  
1
Press T-SET.  
PROGRAM NUMBER  
DATE 05 /12 MON  
START TIME 07: 30 PM  
END TIME 08: 30 PM  
CHANNEL 16  
4
¡If the DVD output mode is selected, you have to  
switch it to the VCR mode by pressing the VCR on  
the remote control or the OUTPUT on the VCR.  
Press K or L repeatedly for the  
desired tape speed. Then, press B.  
REC SPEED SP  
SP  
SLP  
2
3
Select main menu by pressing MENU.  
5
6
To set another program, repeat step [4]. To  
exit, press CLEAR/C.RESET.  
Select "TIMER PROGRAMMING" by press-  
ing K or L. Then, press B.  
Press T-SET to set the timer.  
¡The TIMER light on the DVD/VCR COMBINA-  
TION UNIT comes on. TIMER RECORDING  
WILL NOT BE ACTIVATED UNLESS YOU  
PRESS T-SET.  
4
Select the program number you want to  
check by pressing K or L.  
¡The details of the selected program appears on the  
TV screen.  
HINTS FOR TIMER  
RECORDING  
¡Go to the digit you want to change by pressing B or  
s. Then, enter correct numbers by pressing o or p.  
¡You may cancel the entire program by pressing  
s
VCR  
while the program number flashes.  
¡If there is a power failure or the VCR is unplugged  
for more than 30 seconds, the clock setting and all  
timer settings will be lost.  
5
6
Press CLEAR/C.RESET to exit.  
Press T-SET to return to timer stand-by mode  
.
EN  
20  
 
1L25  
SPECIAL FEATURES  
COPYING A VIDEO TAPE  
5
6
Press REC on the recording VCR.  
VCR  
Begin playback of the tape in the playing  
VCR.  
You can make copies of video tapes made by friends or  
relatives for your enjoyment.  
You can not copy a DVD to a videotape.  
Warning:  
¡For best results during dubbing, use the VCR’s front  
panel controls whenever possible. The remote con-  
trol might affect the playing VCR’s operation.  
¡Always use video-quality shielded cables with  
RCA-type connectors. Standard audio cables are not  
recommended.  
¡You can use a video disc player, satellite receiver, or  
other audio/video component with A/V outputs in  
place of the playing VCR.  
Unauthorized recordings of copyrighted video tapes  
may be an infringement of copyright laws.  
Connect the recording VCR (this unit), the playing  
VCR (another source) and your TV using the follow-  
ing diagram.  
¡You can use the AUDIO/VIDEO input jacks on the  
front panel of the DVD/VCR instead of using the TO MONITOR THE RECORDING  
jacks on the back.  
1
Turn on the TV and set the TV to channel 3.  
[Recording VCR]  
(this unit)  
¡If noise appears, change the RF output channel of  
the VCR to channel 4 by pressing PLAY for 3 sec-  
onds during playback. Then select the same channel  
(CH4) on your TV. (See “RF OUTPUT  
CHANNEL” on page 13 for the detail).  
DVD  
DVD/VCR  
VCR  
AUDIO OUT  
S-VIDEO COMPONENT AUDIO  
DIGITAL  
AUDIO OUT  
OUT  
VIDEO OUT  
OUT  
ANT-IN  
L
Y
AUDIO IN  
Cb  
Cr  
L
R
COAXIAL  
ANT-OUT  
VIDEO OUT  
VIDEO IN  
R
2
Press VCR/TV on the recording VCR.  
RF cable  
(supplied)  
Audio/Video cables  
(not supplied)  
[TV set]  
(Use for monitoring)  
AUTO REWIND  
OUT IN  
AUDIO  
When a tape reaches the end during recording, play-  
back, or fast-forward, the tape will automatically  
rewind to the beginning. After rewinding finishes, the  
VCR will eject the tape and switch itself off.  
¡The VCR will not rewind the tape automatically dur-  
ing timer recording or One Touch Recording.  
VIDEO  
[Playing VCR]  
(another source)  
ANT in  
1
Insert a pre-recorded tape into the playing VCR.  
2
3
4
Insert a tape with a safety tab into the  
recording VCR.  
REAL TIME TAPE COUNTER  
¡This shows the elapsed recording or playback time  
in hours, minutes, and seconds. (The displayed time  
will not change during blank portions of the tape.)  
¡The indication will appear when the tape is rewound  
further than “0:00:00” on the tape counter.  
Press SPEED on the recording VCR to select  
the desired recording speed (SP/SLP)  
.
Select the “L1” or “L2”position on the  
recording VCR.  
¡When you use the A/V input jacks on the back of the  
DVD/VCR, select "L1" position by pressing [0], [0],  
[1] on the remote control or the CH-(UP/DOWN).  
¡When you use the A/V input jacks on the front of the  
DVD/VCR, select "L2" position by pressing [0], [0],  
[2] on the remote control or the CH-(UP/DOWN).  
EN  
21  
 
1L25  
PLAYING A DISC  
Notes  
BASIC PLAYBACK  
¡A “prohibited icon” may appear at the top-right on  
the TV screen during operation, warning that a pro-  
hibited operation has been encountered by the DVD  
or the disc.  
DVD-V  
CD  
Getting started  
¡With DVDs that use titles for playback program sig-  
nals, playback may start from the second title, or it  
may skip these titles.  
¡During the playback of a two layered disc, pictures  
may stop for a moment. This happens when the 1st  
layer switches to the 2nd layer. This is not a mal-  
function.  
¡Turn on the power of the TV, amplifier and any other  
components which are connected to the DVD.  
¡Make sure the TV and audio receiver (commercially  
available) are set to the correct channel.  
¡Select DVD mode by pressing DVD on the remote  
control or OUTPUT on the front panel.  
1
2
Press POWER.  
Press OPEN/CLOSE to open disc loading  
tray.  
GENERAL FEATURES  
DVD may contain menus to navigate the disc and  
access special features. Press the appropriate Number  
buttons or use Arrow (L/K/s/B) to highlight your  
selection in the DVD main menu and press ENTER to  
confirm.  
3
Place the chosen disc in the tray, with the  
label facing up.  
Note  
¡Unless stated, all operations described are based on  
remote control use. Some operations can be carried  
out using the menu bar on the TV screen.  
PAUSE  
4
Press PLAY.  
DVD-V  
CD  
¡The tray will close automatically, and playback will  
then start from the first chapter or track of the disc.  
If the playback does not start automatically, press  
PLAY.  
¡When you playback the DVD which a title menu is  
recorded, it may appear on the screen. In this case,  
refer to “TITLE MENU” on page 23.  
1
During playback, press PAUSE.  
¡Playback will pause and sound will be muted.  
2
To continue playback, press PLAY.  
5
Press STOP twice to stop playback.  
EN  
22  
 
1L25  
DISC MENU  
RESUME  
DVD-V  
DVD-V  
CD  
1
Press MENU.  
¡The DVD main menu will appear.  
1
During playback, press STOP.  
¡Resume message will appear on the TV screen.  
¡To cancel resume, press STOP one more time.  
2
3
If the feature is not available,  
may appear on the TV screen.  
symbol  
2
Press PLAY, playback will resume from the  
point at which playback was stopped.  
If disc menu is available on the disc, audio  
language, subtitle options, chapters for the  
title and other options will appear for selec-  
tion.  
FAST FORWARD/REVERSE  
SEARCH  
DVD-V  
CD  
MP3  
4
Press Arrow (L/K/s/B) to select an item,  
and ENTER to confirm selection.  
1
During playback, press g or h repeat-  
edly to select the required forward or  
reverse speed: x2, x8, x50, x100.  
TITLE MENU  
DVD-V ¡When using the FWD or REV button on the front  
panel, press the button during playback, and hold it  
for more than 1.5 seconds to chang the  
1
Press TITLE.  
¡The title menu will appear.  
forward/reverse speed: ×2, ×8, ×50, ×100.  
¡For audio CDs, the speed is fixed at ×16.  
¡For MP3, the speed is fixed at ×8.  
2
3
If the feature is not available,  
may appear on the TV screen.  
symbol  
2
To return to normal playback, press PLAY .  
Press Arrow (L/K/s/B) to select an item,  
SLOW FORWARD /  
SLOW REVERSE  
and ENTER to confirm selection.  
DVD-V  
During playback, press PAUSE.  
Press g or h .  
CALLING UP A MENU SCREEN  
DURING PLAYBACK  
1
2
3
¡Press MENU to call up the DVD menu.  
¡Press TITLE to call up the title menu.  
Note  
¡Contents of menus and corresponding menu opera-  
tions may vary between discs. Refer to the manual  
accompanying the disc for details.  
Press g or h repeatedly to select the  
required speed: 1/16, 1/8, 1/2 of the normal  
playback.  
¡When using the FWD or REV button on the front  
panel, press the button in PAUSE mode, and hold it  
for more than 1.5 seconds to chang the  
STEP BY STEP PLAYBACK  
forward/reverse speed: ×1/16, ×1/8, ×1/2.  
DVD-V  
4
To return to normal playback, press PLAY.  
1
During playback, press PAUSE.  
¡Playback will pause and sound will be muted.  
2
3
The disc goes forward by one frame each  
time PAUSE is pressed.  
To exit step by step playback, press PLAY.  
EN  
23  
 
1L25  
Using SKIP  
H
,
G
ZOOM  
During playback, press SKIP G to move the next  
track. Press it repeatedly to skip subsequent tracks.  
Press SKIP H to go back to beginning of the current  
track. Press it repeatedly to go to the previous tracks.  
¡If SKIP is pressed while the playback is paused, the  
playback will be paused again after skipping to the  
next track.  
DVD-V  
The Zoom function allows you to enlarge the video  
image and to pan through the enlarged image.  
1
Press ZOOM during playback.  
¡Playback will continue.  
Note  
¡SKIP H , G are not available when playback is  
stopped.  
2
3
Press ZOOM repeatedly to select the  
required zoom factor: x2, x4 or OFF.  
TITLE / CHAPTER SEARCH  
Use the Arrow (K/L/s/B) to move the  
zoomed picture across the screen.  
DVD-V  
4
To exit zoom mode, press ZOOM to OFF.  
1
Press SEARCH MODE once for the Chapter  
search, twice for the Title Search during  
playback.  
Notes  
¡Zooming function does not work while disc menu is  
shown.  
/2  
¡x4 zoom is not available on some discs.  
TRACK  
2
Enter the desired chapter/title number using  
the Number buttons.  
CD  
¡Playback will start at the selected Chapter or Title.  
¡Press CLEAR/C.RESET to erase the incorrect input.  
¡For single digits press 0 first.  
There are three ways to begin playback on an Audio  
CD at a specific Track.  
Using the Number buttons  
TIME SEARCH  
1
Press the Number buttons to enter the  
desired Track number.  
DVD-V  
CD  
¡Playback will start at the selected track.  
¡For single digit tracks (1-9), press a single number  
(eg. track 3, press 3).  
¡To play track 26, press +10, 2, 6 on the Number but-  
tons.  
1
2
During playback, press SEARCH MODE  
three times (CD: twice) to display the Time  
Search on the TV screen.  
Within 30 seconds, enter a desired disc  
time using the Number buttons.  
Using SEARCH MODE  
1
Press SEARCH MODE.  
¡The track search display appears.  
¡Playback will start at the specified time.  
¡Press CLEAR/C.RESET to erase the incorrect input.  
2
Within 30 seconds, select a desired track  
number using the Number buttons.  
¡For single digits press 0 first.  
¡Playback will start at the selected track.  
EN  
24  
 
1L25  
Notes  
REPEAT  
REPEAT is available only during playback.  
REPEAT TITLE / CHAPTER  
¡The A-B REPEAT section can only be set within the  
current title (for DVDs), or current track (for audio  
CDs).  
¡A-B REPEAT is not available with some scenes in  
DVD.  
¡To cancel the A point which was set, press  
CLEAR/C.RESET.  
¡A-B REPEAT playback does not function during  
title, chapter, track or all repeat playback.  
DVD-V  
To activate the repeat function, press REPEAT  
during playback.  
¡The repeat mode changes as described below every  
time you press the button.  
CHAPTER  
(current chapter repeat) (current title repeat)  
TITLE  
OFF  
(repeat off)  
PROGRAM  
CD  
Notes  
You may determine the order in which tracks will play.  
¡Repeat Title/Chapter is not available with some  
scenes.  
¡The REPEAT setting will be cleared when moving  
to other title or chapter.  
1
In stop mode, press MODE.  
¡The PROGRAM screen will appear.  
REPEAT TRACK  
2
Press or to select a track, then press  
ENTER.  
To activate the repeat function, press REPEAT  
during playback.  
¡The repeat mode changes as described below every  
time you press the button.  
¡Press CLEAR/C.RESET  
to erase the most recently  
entered program.  
CD [AUDIO]  
T
TOTAL 0:03:30  
T
T
T
T
T
T
T
Notes  
T
¡Track repeat setting will be cleared when moving to  
other track.  
¡Repeat playback does not function during A-B  
REPEAT playback.  
3
Notes  
Press PLAY to play the programmed tracks.  
CD  
¡While the program is being played back, the STOP  
works as follows.  
TRACK  
(current track repeat)  
ALL  
OFF  
(repeat off)  
(entire disc repeat)  
¡Press STOP once and then PLAY again, playback  
will restart from the point where STOP was pressed.  
(Program continued)  
¡Press STOP twice and then PLAY again, playback  
will restart from the track in the usual way. (Program  
cleared)  
MP3  
TRACK  
GROUP  
(current group  
repeat)  
ALL  
OFF  
(repeat off)  
(current track  
(entire disc  
repeat)  
¡Up to 99 programs can be entered.  
¡If you like to repeat the current track in the program,  
repeat)  
press REPEAT repeatedly until  
TRACK appears  
during playback. If you like to repeat the entire pro-  
A-B REPEAT  
gram press REPEAT repeatedly until  
appears during playback.  
ALL  
DVD-V  
CD  
1
2
Press REPEAT A-B at your chosen starting  
point.  
A- appears briefly on the TV screen.  
¡
¡
Press REPEAT A-B again at your chosen  
end point.  
A-B appears briefly on the TV screen, and the  
repeat sequence begins.  
3
To exit the sequence, press REPEAT A-B.  
EN  
25  
 
1L25  
Notes  
RANDOM PLAYBACK  
¡Folders are known as Groups; files are known as  
Tracks.  
¡MP3 files are accompanied by  
CD  
3
icon.  
¡Maximum of 255 folders can be recognized.  
¡Maximum of 256 files can be recognized.  
¡Up to 8 hierarchies can be created.  
This shuffles the playing order of tracks instead of  
playback in the sequence.  
This player recommends the use of files recorded at  
the below specifications:  
¡Sampling frequency: 44.1kHz or 48kHz  
¡Constant bit rate: 112kbps ~ 320kbps.  
1
In stop mode, press MODE twice.  
¡RANDOM screen  
RANDOM  
appears.  
CD [AUDIO]  
TOTAL 0:45:55  
RANDOM PROGRAM  
--no indication--  
PLAY  
INFORMATION  
ON-SCREEN  
MP3  
You can check the MP3 files during playback.  
2
Press PLAY to start random playback.  
Note  
1
Press DISPLAY.  
¡The name of the file currently in play will be dis-  
¡If you like to repeat the current track in the random  
selection, press REPEAT repeatedly until  
TRACK appears during playback. If you like to  
repeat the entire random selection press REPEAT  
played.  
2
Press DISPLAY again to show the track  
number, the repeat status, and the playback  
status at the top of the screen.  
repeatedly until  
ALL appears during playback.  
MP3 PLAYBACK  
¡
will be displayed when repeat play has been  
selected.  
MP3  
T - indicates Track repeat  
When a CD with MP3 files is inserted in the  
DVD/VCR, the MP3 menu will appear on the TV  
screen.  
G - indicates Group (folder) repeat  
A - indicates Disc repeat  
1
In stop mode, press Arrow (K/L) to select  
the desired group track.  
3
1
Press DISPLAY again to exit.  
¡If a group is selected, press B or ENTER to go on to  
the track selection screen.  
Press Arrow (K /L ) to  
choose a track, then press  
B or ENTER.  
TRACK SELECTION  
MP3  
Press SEARCH MODE during playback.  
¡The FILE LIST will appear.  
¡If a track is selected, press  
B or ENTER to start play-  
ing tracks. Starting from  
the one you’ve just chosen the subsequent tracks  
will be played.  
¡Choose FIRST PLAY to start playback from the  
beginning of the listed tracks.  
¡Press TITLE to return to the first item.  
2
Select a desired track using Arrow  
(K/L/s/B).  
¡Press B when you want to go to the next hierarchy.  
¡Press s when you want to go back to the previous  
hierarchy.  
3
Notes  
Press PLAY to start playing.  
2
Press STOP to stop playback.  
¡Press SEARCH MODE to exit.  
¡Some selections may take a while to be recognized.  
EN  
26  
 
1L25  
RANDOM PLAYBACK  
SUBTITLE LANGUAGE  
MP3  
DVD-V  
The DVD allows you to select a language for subtitles  
during DVD disc (if available) playback.  
1
2
Press MODE twice while playback is  
stopped.  
1
2
Press SUBTITLE during playback.  
Press PLAY to play the tracks in random  
order.  
Press SUBTITLE repeatedly to select your  
desired subtitle language.  
PROGRAM  
¡The subtitle language will be displayed on the dis-  
play bar at the top of the screen.  
MP3  
3
To turn off subtitles, press SUBTITLE  
repeatedly until OFF appears.  
This feature allows you to program a mp3 disc to play  
in a desired sequence.  
Notes  
¡Pressing AUDIO may not work on some DVDs with  
multiple audio languages (e.g. DVDs which allow  
audio language setting on the disc menu).  
¡Some discs allow audio language setting/subtitle  
language setting on the disc menu. (Operation varies  
between discs, so refer to the manual accompanying  
the disc.)  
1
Press MODE during playback is stopped.  
¡The PROGRAM screen will appear.  
2
Press Arrow (K/L) to select a track, then  
press ENTER, to save it in a program.  
¡Press CLEAR/C.RESET to erase the incorrect input.  
¡If the desired language is not shown after pressing  
SUBTITLE several times, the disc does not have  
subtitles in that language.  
3
Press PLAY to start programmed playback.  
¡If you choose a Language that has a 3 letter language  
code, the code will be displayed every time you  
change the Subtitle language setting. If you choose  
any other languages, ‘---’ will be displayed instead.  
(Refer to page 31.)  
AUDIO LANGUAGE  
DVD-V  
The DVD/VCR allows you to select a language during  
DVD disc (if multi language available) playback.  
CAMERA ANGLE  
DVD-V  
1
2
Press AUDIO during playback.  
Some DVD discs contain scenes which have been shot  
simultaneously from various angles. You can change  
Press AUDIO repeatedly to select your  
desired language.  
the camera angle when the (  
screen.  
) icon appears on the  
STEREO SOUND MODE  
1
Press ANGLE during playback.  
CD  
¡The selected angle will be displayed on the display  
bar at the top of the screen.  
1
Press AUDIO repeatedly during playback to  
select between STEREO, L-CH or R-CH.  
2
Press ANGLE repeatedly to select your  
desired angle.  
¡STEREO - both right and left channels are active  
(stereo)  
L-CH - only left channel is active  
R-CH - only right channel is active  
Note  
¡If the Virtual Surround setting is ON, the sound  
mode will be fixed to STEREO, and can not be  
changed.  
EN  
27  
 
1L25  
CHANGING THE ON-SCREEN  
DISPLAY  
PARENTAL CONTROL  
DVD-V  
DVD-V  
CD  
Parental Control limits the disc viewing that exceed  
your settings. (with a password or playback will stop.)  
This feature allows you to prevent discs with alterna-  
tive scenes from being played by your children.  
You can check the information about the current disc  
by pressing DISPLAY on the remote control.  
For DVD-Vs  
PARENTAL LEVEL  
1
Press DISPLAY during playback to show  
current Chapter.  
Parental Level allows you to set the rating level of  
your DVD discs. Playback will stop if the disc’s rat-  
ings exceed the level you set.  
¡The elapsed and remaining  
playing time of the current  
chapter will be displayed.  
9/49  
0:00:00 -0:00:00  
1
2
Press SETUP in STOP mode.  
Press B to select CUSTOM, then press  
ENTER.  
2
Press DISPLAY again to show current Title.  
¡The elapsed and remaining playing time of the cur-  
rent title will be displayed.  
3
Press Arrow (s/B) to select PARENTAL,  
then press ENTER.  
3
Press DISPLAY third time.  
¡The BIT RATE and the current repeat setting will be  
displayed.  
PARENTAL  
PARENTAL LEVEL ALL  
¡If you are playing a dual layered disc, the layer num-  
ber will also be displayed (L0: Layer 0 is playing.  
L1: Layer 1 is playing).  
4
5
6
Enter your four-digit password then press  
ENTER.  
4
Press DISPLAY the fourth time to remove  
the display.  
Press Arrow (K/L) to select PARENTAL  
LEVEL, then press ENTER.  
For audio CDs  
1
Press DISPLAY during playback, the current  
Track will be displayed on the TV screen.  
Press Arrow (K/L) to select the desired  
level.  
¡The elapsed and remaining playing time of the cur-  
rent track will be displayed.  
7
Notes  
Press SETUP to exit  
¡When doing this for the first time, enter any 4 digits.  
(except for 4737) That number will be used as the  
password. (in the event you forget the password, see  
below.)  
¡To change the password, press Arrow (K/L) to  
select CHANGE at step 5, then press ENTER. Enter  
the four-digit pass-word, then press ENTER.  
¡With some DVDs, it may be difficult to find if they  
are compatible with parental lock. Be sure to check  
if the parental lock function operates in the way that  
you have set.  
2
Press DISPLAY again to show current Total  
Track.  
¡The elapsed and remaining playing time of the cur-  
rent total track will be displayed.  
3
Press DISPLAY third time to remove the dis-  
play.  
¡Record the password in case you forget it.  
IF YOU FORGET THE PASSWORD  
1
Press 4, 7, 3, 7 at step 4. Then enter your  
new password.  
¡Password will be cleared and parental level will be  
set to ALL.  
2
Proceed the above Steps 5-7 again.  
EN  
28  
 
1L25  
CONTROL LEVELS  
2
3
Press Arrow (s /B) to select 1, 2, 3, 4, 5, 6,  
7, 8, 9, or 10 and ensure that “- : - - : - -”  
appears in the display.  
¡ALL  
All parental lock is cancelled.  
¡Level 8  
DVD software of any grade (adult/general/children)  
can be played back.  
When reaches the desired point, press  
ENTER.  
¡Levels 7 to 2  
¡The Title or Track and elapsed playing time will  
appear in the TV screen.  
Only DVD software intended for general use and  
children can be played back.  
¡
Level 1  
4
To return to the Marker later, press SEARCH  
MODE four times (CD: three times) during  
playback and Arrow (s /B) to choose the  
desired marker, then press ENTER.  
Only DVD software intended for children can be  
played back, with those intended for adult and  
general use prohibited.  
Notes  
¡Opening the disc tray or turning off the power or  
select AC at step 2 and press ENTER will erase all  
Markers.  
MARKER SETUP SCREEN  
DVD-V  
CD  
¡To clear a marker, using Arrow (s /B), position the  
cursor on to the marker number to be cleared and  
press CLEAR/C.RESET.  
¡You can mark up to 10 points.  
Use markers to memorise your favourite places on a  
disc.  
1
Press SEARCH MODE four times (CD: three  
times) during playback.  
5
Press SEARCH MODE or RETURN to exit.  
¡The display screen and Markers will appear on the  
TV screen.  
DVD SETUP  
Dolby Digital:  
Set to On when the unit is connected to a Dolby Digital  
QUICK  
AUDIO SETTING  
Choose the appropriate Audio settings for your equip-  
ment as it only affect during the playback of DVD  
discs.  
Receiver.  
(ON: Outputs a Dolby Digital Signal)  
(OFF: Convert the Dolby Digital to PCM (2channel))  
¡The default setting is ON.  
DOWN SAMPLING:  
¡Set to ON when outputting in 48 kHz.  
¡The default setting is ON.  
When playing disc with copyright Protection  
¡If you select OFF, copyright protection will be acti-  
vated and sound will be down sampled at 48kHz.  
1
2
Press SETUP in STOP mode.  
Press B to select CUSTOM, then press  
ENTER.  
¡CUSTOM mode will appear.  
3
Press Arrow (s / B) to select AUDIO, then  
press ENTER to confirm.  
5
Press SETUP to exit.  
AUDIO  
DRC  
OFF  
ON  
DOLBY DIGITAL  
DOWN SAMPLING ON  
4
Press Arrow (K/L) to select the below  
items, then press ENTER.  
DRC (Dynamic Range Control):  
¡To compress the range of soft to loud sounds.  
¡The default setting is OFF.  
EN  
29  
 
1L25  
BLACK LEVEL SETTING  
DISPLAY SETTING  
DVD-V  
DVD-V  
Adjust the Black Level Settings to make the black You can change certain aspects of the DVD display  
parts of the picture brighter. screens, and on-screen messages.  
1
Press MODE during playback.  
1
2
Press SETUP in STOP mode.  
ON  
Press B to select CUSTOM, then press  
ENTER.  
¡CUSTOM mode will appear.  
2
Press ENTER to switch ON/OFF.  
ON: Makes the dark parts brighter.  
3
Press Arrow (s /B) to select DISPLAY, then  
press ENTER to confirm.  
OFF: Shows the original picture as recorded.  
3
Press MODE twice or RETURN to exit.  
DISPLAY  
TV ASPECT  
4:3 LETTER BOX  
ON  
ANGLE ICON  
AUTO POWER OFF ON  
VIRTUAL SURROUND  
DVD-V  
CD  
MP3  
4
Press Arrow (K/L) to select the below  
items, then press ENTER.  
You can enjoy stereophonic virtual space on your  
existing stereo system.  
TV ASPECT:  
¡Press Arrow (K/L) for an item selection, then press  
QUICK  
ENTER.  
1
Press MODE twice (CD/MP3: once) during  
¡Select 4:3 LETTER BOX for a black bars appears  
on top and bottom of the screen.  
¡Select 4:3 PAN & SCAN for a full height picture  
with both sides trimmed.  
playback.  
OFF  
¡Select 16:9 WIDE if a wide-screen TV is connected  
to the DVD/VCR.  
¡The default setting is 4:3 LETTER BOX.  
ANGLE ICON:  
¡Press ENTER repeatedly to turn Angle icon ON or  
OFF.  
¡The default setting is ON.  
AUTO POWER OFF:  
¡Press ENTER repeatedly to turn Auto Power off ON  
or OFF.  
2
3
Press ENTER to set it 1 (Natural effect) or 2  
(Emphasized effect) or OFF.  
Press MODE or RETURN to exit.  
Note (for CD play only)  
¡Virtual Surround will not be effective if the sound  
mode is set to something other than STEREO.  
¡The default setting is ON and it will turn the  
DVD/VCR to off automatically after 35 minutes of  
no use.  
5
Press SETUP to exit.  
Note  
¡Be sure to press SETUP, or the setting will not work.  
EN  
30  
 
1L25  
AUDIO:  
¡Sets the audio language.  
SUBTITLE:  
¡Sets the subtitle language.  
DISC MENU:  
¡Sets the language for DVD menu.  
LANGUAGE SETTING  
DVD-V  
Language options are not available with some discs.  
PLAYER MENU:  
¡Sets the language for the On-screen display.  
QUICK  
1
2
Press SETUP in STOP mode.  
Press B to select CUSTOM, then press  
ENTER.  
5
Press Arrow (K/L) to select a setting, then  
press ENTER.  
¡CUSTOM mode will appear.  
¡If OTHER is selected on the AUDIO, SUBTITLE or  
DISC MENU screen, press four-digit number to  
enter the code for the desired language. (Refer to the  
language code list below.)  
3
Press Arrow (s / B) to select LANGUAGE,  
then press ENTER to confirm.  
¡Only the languages supported by the disc can be  
selected.  
LANGUAGE  
AUDIO  
ORIGINAL  
OFF  
ENGLISH  
ENGLISH  
6
Note  
Press SETUP to exit.  
SUBTITLE  
DISC MENU  
PLAYER MENU  
¡Language Setting for Audio and Subtitle is not avail-  
able with some discs. Then use the Audio and the  
Subtitle button. Details are on page 27.  
4
Press Arrow (K/L) to select the next items,  
then press ENTER.  
¡If you want to return to LANGUAGE SETTING  
MENU, press Arrow (s ).  
Language  
Code  
Language  
Frisian  
Code  
5271  
5358  
5747  
5051  
5158  
5758  
5360  
5367  
5447  
5569  
5455  
5467  
Language  
Malay  
Code  
5965  
5958  
5966  
5955  
5964  
5961  
5960  
6047  
6051  
6061  
Language  
Somali  
Spanish [SPA]  
Sundanese  
Swahili  
Swedish [SWE]  
T
Code  
6561  
5165  
6567  
6569  
6568  
A-B  
Abkhazian  
Afar  
Afrikaans  
Albanian  
Amharic  
Arabic  
Armenian  
Assamese  
Aymara  
Azerbaijani  
Bashkir  
Basque  
Bengali;Bangla  
Bhutani  
Bihari  
Bislama  
Breton  
4748  
4747  
4752  
6563  
4759  
4764  
5471  
4765  
4771  
4772  
4847  
5167  
4860  
5072  
4854  
4855  
4864  
4853  
5971  
4851  
Galician  
Malayalam  
Maltese  
Maori  
Georgian  
German [GER]  
Greek [GRE]  
Greenlandic  
Guarani  
Gujarati  
Hausa  
Hebrew  
Hindi  
Hungarian [HUN]  
I-K  
Icelandic [ICE]  
Indonesian  
Interlingua  
Interlingue  
Inupiak  
Irish [IRI]  
Italian [ITA]  
Japanese [JPN]  
Javanese  
Kannada  
Kashmiri  
Kazakh  
Kinyarwanda  
Kirghiz  
Kirundi  
Marathi  
Moldavian  
Mongolian  
Nauru  
Tagalog  
Tajik  
Tamil  
6658  
6653  
6647  
6666  
6651  
6654  
4861  
6655  
6661  
6665  
6664  
6657  
6669  
Nepali  
Norwegian [NOR]  
O-R  
Occitan  
Tatar  
Telugu  
6149  
6164  
6159  
6247  
6265  
5247  
6258  
6266  
6367  
6459  
6461  
6467  
Thai  
Oriya  
Oromo(Afan)  
Panjabi  
Pashto;Pushto  
Persian  
Polish  
Portuguese [POR]  
Quechua  
Rhaeto-Romance  
Romanian [RUM]  
Russian [RUS]  
S
Samoan  
Sangho  
Sanskrit  
Scots Gaelic  
Serbian  
Serbo-Croatian  
Sesotho  
Setswana  
Shona  
Sindhi  
Tibetan  
Tigrinya  
Tonga  
5565  
5560  
5547  
5551  
5557  
5347  
5566  
5647  
5669  
5760  
5765  
5757  
6469  
5771  
6460  
5761  
5767  
Tsonga  
Turkish [TUR]  
Turkmen  
Twi  
Bulgarian  
Burmese  
Byelorussian  
U-Z  
Ukrainian  
Urdu  
Uzbek  
6757  
6764  
6772  
6855  
6861  
4971  
6961  
7054  
5655  
7161  
7267  
C-E  
Cambodian  
Catalan  
5759  
4947  
7254  
4961  
5464  
4965  
5047  
6058  
5160  
5161  
5166  
Vietnamese  
Volapuk  
Welsh  
Wolof  
Xhosa  
Yiddish  
Yoruba  
Zulu  
Chinese [CHI]  
Corsican  
Croatian  
6559  
6553  
6547  
5350  
6564  
6554  
6566  
6660  
6560  
6550  
6555  
6565  
6557  
6558  
Czech  
Danish [DAN]  
Dutch [DUT]  
English [ENG]  
Esperanto  
Estonian  
Korean [KOR]  
Kurdish  
L-N  
Laothian  
Latin  
Latvian;Lettish  
Lingala  
Lithuanian  
Macedonian  
Malagasy  
5861  
5847  
5868  
5860  
5866  
5957  
5953  
F-H  
Faroese  
Fiji  
Finnish [FIN]  
French [FRE]  
5261  
5256  
5255  
5264  
Singhalese  
Siswat  
Slovak  
Slovenian  
If you choose a Language that has a 3 letter language code, the code will be displayed every time you change  
the Audio or Subtitle language setting on page 27. If you choose any other languages, ‘---’ will be displayed  
instead. (3 letter language code is written in bracket.)  
EN  
31  
 
1L25  
TROUBLESHOOTING GUIDE  
If the DVD/VCR COMBINATION UNIT does not perform properly when operated as instructed in this  
Owner's Manual, check the player consulting the following checklist.  
PROBLEM  
No power.  
CORRECTIVE ACTION  
D
V
D
• Make sure the power plug is connected to an AC outlet.  
• Make sure the power is turned on.  
The player does not respond to. • Check if the power plug is connected to an AC outlet.  
the remote control.  
• Check the batteries in the remote control.  
• Aim the remote control directly at the remote sensor. If necessary, remove all the  
obstacles between the sensor and the remote.  
You have to be within 7 m (23 feet) of the player.  
• Check if the correct mode is selected. If not switch the mode by pressing DVD or  
VCR ,whichever you need, on the remote control.  
V
C
R
• Check if a cassette tape is in the VCR.  
Timer recording is impossible. • Make sure the timer recording is set correctly.  
• Make sure the power is off.  
V
C
R
• Make sure the VCR clock is set correctly.  
Cannot go into Record mode. • Make sure the tape has a safety tab. If needed, cover the hole with cellophane tape.  
• Put the player in VCR mode. Press VCR on the remote control so that the green VCR  
OUTPUT light is lit.  
Playback picture is partially noisy  
Adjust tracking control for a better picture by pressing SKIP/CH. (o/p) on the remote  
or CH-(UP/DOWN) on the DVD/VCR COMBINATION UNIT.  
Cannot view a tape but the  
• Head cleaning may be necessary. Refer to “AUTO HEAD CLEANING” .  
• Make sure the VCR is not in the Menu mode.  
.
audio is OK  
No, or poor, playback picture.  
• Change the RF output channel to CH4. Then select the same channel on the TV.  
• Fine tune your TV.  
TV programs cannot be seen  
normally.  
• Re-check the ANT. IN and ANT. OUT connections. See page 13.  
• Press VCR/TV.  
• Press VCR on the remote control to put it in the VCR mode. Check if the green VCR  
OUTPUT light is lit. Then, set it to the TV position by pressing VCR/TV.  
Video or color fades in and out  
when making a copy of a video tape.  
You cannot copy a copyrighted video tape. You are experiencing copy guard protection.  
Cannot remove the tape.  
• Check if the player is in the VCR mode. If not, press VCR on the remote control to switch  
the mode.  
No picture.  
• Connect the video cables firmly.  
D
V
D
• Insert a correct video disc that plays on this player.  
• Press DVD on the remote control. Check if the DVD OUTPUT Light is lit. Then try other  
DVD feature.  
• Insert the disc.  
• Clean the disc.  
.
Disc cannot be played  
• Place the disc correctly, with the label side up.  
• Cancel the parental lock or change the control level.  
• Connect the audio cables firmly.  
.
No sound  
Turn the power of the audio component on.  
• Correct the audio output settings.  
• Correct the input settings on the audio component.  
• This player does not support DTS audio. This is not a malfunction.  
• Connect the player directly to the TV.  
.
No DTS audio is output  
.
Distorted picture  
There are some cases where pictures may be slightly distorted, which are not a sign of a mal-  
function.  
• Although pictures may stop for a moment, this is not a malfunction.  
Audio or subtitle language  
does not match the set up  
The camera angle cannot be  
changed  
The selected language is not available for audio or subtitles on the DVD.  
This is not a malfunction  
The DVD does not contain sequences recorded from different camera angles.  
This is not a malfunction  
Audio or subtitle language  
cannot be changed  
• The DVD does not contain audio source or subtitles in the selected language.  
This is not a malfunction.  
“Prohibited icon” appears on the • That operation is prohibited by the player or the disc.  
screen, prohibiting an operation This is not a malfunction.  
Notes  
Some functions are not available in specific modes, but this is not a malfunction. Read the description in this  
Owner’s Manual for details on correct operations.  
¡Playback from a desired track and random playback are not available during program playback.  
EN  
32  
 
1L25  
MAINTENANCE  
SERVICING  
AUTO HEAD CLEANING  
¡Should your DVD/VCR COMBINATION UNIT ¡Automatically cleans video heads as you insert or  
become inoperative, do not try to correct the prob- remove a cassette, so you can see a clear picture.  
lem by yourself. There are no user-serviceable parts ¡Playback picture may become blurred or interrupted  
inside. Turn off, unplug the power cord, and take the  
unit to our Authorized Service Center.  
while the TV program reception is clear. Dirt accu-  
mulated on the video heads after long periods of use,  
or the usage of rental or worn tapes can cause this  
problem. If a streaky or snowy picture appears dur-  
ing playback, the video heads in your DVD/VCR  
COMBINATION UNIT may need to be cleaned.  
CLEANING THE CABINET  
¡Use a soft cloth slightly moistened with a mild deter-  
gent solution. Do not use a solution containing alco-  
hol, spirits, ammonia or abrasives.  
1. Please visit your local Audio/Video store and pur-  
chase a good quality VHS Video Head Cleaner.  
CLEANING DISCS  
2. If a Video Head Cleaner does not solve the prob-  
lem, consult our nearest Authorized Service Center.  
¡When a disc becomes dirty, clean it with a cleaning  
cloth. Wipe the disc from the center out. Do not wipe  
in a circular motion.  
NOTES:  
¡Do not use solvents such as benzine, thinner, com-  
mercially available cleaners, detergent, abrasive  
cleaning agents or antistatic spray intended for ana-  
logue records.  
¡Remember to read the instructions included with the  
video head cleaner before use.  
¡Clean video heads only when problems occur.  
CLEANING THE DISC LENS  
¡If the player still does not perform properly when it  
is operated while referring to the relevant sections  
and to “TROUBLESHOOTING GUIDE” in this  
Owner’s Manual, the laser optical pickup unit may  
be dirty. Consult your dealer or an Authorized  
Service Center for inspection and cleaning of the  
laser optical pickup unit.  
DISC HANDLING  
¡Use discs which have the following logos on them.  
(Optical audio digital discs.)  
Recordable  
ReWritable  
¡Handle the discs so that fingerprints and dust do not  
adhere to the surfaces of the discs.  
¡Always store the disc in its protective case when it is  
not used.  
Make your contribution to the environment!!!  
¡Used up batteries do not belong in the dust bin.  
¡You can dispose of them at a collection point for used up batteries or special waste.  
Contact your council for details.  
EN  
33  
 
1L25  
SPECIFICATIONS  
Product type:  
Discs:  
DVD player with Video Cassette Recorder  
DVD video  
Audio CD  
Video Cassette tape  
Converter output:  
Power source:  
VHF Channel 3 or 4.  
120 V AC +/- 10%, 60 Hz +/- 0.5%  
24 W (standby: 7.0 W)  
41˚F (5°C) to 104˚F (40°C)  
W 435 mm (17-1/8”)  
Power consumption:  
Operating temperature:  
Dimensions:  
H 99 mm (3-15/16”)  
D 218 mm (8-9/16”)  
Weight:  
3.7 kg (8.16 lbs)  
¡Designs and specifications are subject to change without notice.  
¡If there is a discrepancy between languages, the default language will be English.  
EN  
34  
 
1L25  
MEMO  
EN  
35  
 
1L25  
FUNAI CORPORATION  
LIMITED WARRANTY  
FUNAI CORP. will repair this product, free of charge in CANADA in the event of defect in materials or workmanship as follows:  
DURATION:  
PARTS:  
FUNAI CORP. will provide parts to replace defective parts without charge for one (1) year from the date of  
original retail purchase. Two (2) years for Picture Tube. Certain parts are excluded from this warranty.  
FUNAI CORP. will provide the labor without charge for a period of ninety (90) days from the date of original  
retail purchase.  
LABOR:  
LIMITS AND EXCLUSIONS:  
THIS WARRANTY IS EXTENDED ONLY TO THE ORIGINAL RETAIL PURCHASER. A PURCHASE RECEIPT OR OTHER  
PROOF OF ORIGINAL RETAIL PURCHASE WILL BE REQUIRED TOGETHER WITH THE PRODUCT TO OBTAIN SER-  
VICE UNDER THIS WARRANTY.  
This warranty shall not be extended to any other person or transferee.  
This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced, missing or if service was  
attempted by AUTHORIZED SERVICE FACILITY. This FUNAI CORPORATION Limited warranty does not apply to any the  
product not purchased and used in CANADA.  
This warranty only covers failures due to defects in material or workmanship which occurs during normal use. It does not cover  
damage which occurs in shipment, or failures which are caused by repairs, alterations or product not supplied by FUNAI CORP.,  
or damage which results from accident, misuse, abuse, mishandling, misapplication, alteration, faulty installation, improper main-  
tenance, commercial use such as hotel, rental or office use of this product or damage which results from fire, flood, lightning or  
other acts of God.  
THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY ACCESSORIES (EXCEPT REMOTE CONTROL),  
ANY COSMETIC PARTS, COMPLETE ASSEMBLY PARTS, DEMO OR FLOOR MODELS.  
FUNAI CORP. AND ITS REPRESENTATIVES OR AGENTS SHALL IN NO EVENT BE LIABLE FOR ANY GENERAL,  
INDIRECT OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR OCCASIONED BY THE USE OF OR THE INABILI-  
TY TO USE THIS PRODUCT. THIS WARRANTY IS MADE IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR  
IMPLIED, AND OF ALL OTHER LIABILITIES ON THE PART OF FUNAI, ALL OTHER WARRANTIES INCLUDING THE  
WARRANTY OF MERCHANTABILITY, AND FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED BY  
FUNAI AND ITS REPRESENTATIVES IN CANADA.  
ALL WARRANTY INSPECTIONS AND REPAIRS MUST BE PERFORMED BY AUTHORIZED SERVICE FACILITY.  
THIS WARRANTY IS VALID WHEN THE UNIT IS CARRIED-IN TO AUTHORIZED SERVICE FACILITY.  
THE PRODUCT MUST BE ACCOMPANIED BY A COPY OF THE ORIGINAL RETAIL PURCHASE RECEIPT. IF NO  
PROOF OF PURCHASE IS ATTACHED, THE WARRANTY WILL NOT BE HONORED AND REPAIRS COSTS WILL BE  
CHARGED.  
ATTENTION:  
FUNAI CORP. RESERVES THE RIGHT TO MODIFY ANY DESIGN OF THIS PRODUCT WITH-  
OUT PRIOR NOTICE.  
To locate your nearest AUTHORIZED SERVICE FACILITY or general service procedure, please contact to us:  
FUNAI CORPORATION  
Customer Service  
100 North Street; Teterboro, NJ 07608 , USA  
Tel: 1-800-242-7158  
PLEASE DO NOT SHIP YOUR UNIT TO THE TETERBORO ADDRESS.  
Printed in China  
0VMN03821  
★★★★★  
 
H9414CD  

Sennheiser Stereo Receiver EM 1031 U User Manual
Snapper Utility Vehicle 63178 User Manual
Sony Camera Lens VCL 2030S User Manual
Sony Headphones 3 095 629 132 User Manual
Sparky Group Battery Charger BUR 15E User Manual
Sprint Nextel Bicycle Bike User Manual
Stamina Products Webcam 25 May User Manual
Stiga Tiller 82R2 H User Manual
Stoelting Blender F131 User Manual
SunBriteTV Flat Panel Television 4610HD User Manual