Tannoy Stereo Amplifier Stereo amplifier Dimension User Manual

O W N E R ’ S  
M A N U A L  
 
AMPLIFIER CHOICE  
Consult the enclosed product specification sheet as this clearly shows the acceptable power range for amplifier matching to  
your speakers. The high peak power handling of Tannoy loudspeakers permits responsible use with more powerful amplifiers  
- please read the Warranty.  
As with all loudspeaker systems, the power handling is a function of voice coil thermal capacity. Care should be taken to  
avoid overdriving any amplifier, as this will cause output overload resulting in 'clipping' or distortion within the output signal.  
This, if done for any extended period, will cause damage to the speakers.  
Generally an amplifier of higher power that is running hard, but free of distortion, will do less damage to the loudspeaker  
than a lower power amplifier continually clipping. Remember also that a high powered amplifier running at less than 90%  
of output power generally sounds a great deal better than a lower powered example struggling to achieve 100%. An amplifier  
with insufficient drive capability will not allow the full performance of the loudspeakers to be realised.  
CABLE CHOICE  
Always use the best quality of cable available within your budget. High quality audio signals passing from the amplifier to  
the loudspeaker are unusual in their demands on the cable. Wide dynamic range and frequency bandwidth information has  
to coexist with the ability to transmit peak currents of at least 10amps, without incurring any loss or signal impairment. This  
explains why the sound quality of the information reproduced by the loudspeakers is so dependant on the physical properties  
of the cables connecting them to the amplifier.  
We would recommend that you always keep the cable runs the same length for each speaker.  
Remember, cable construction can affect the sound quality so be prepared to experiment to find a cable that suits your ear  
and audio system.  
TERMINAL PANEL  
(See fig. 1)  
In order to take advantage of the driver earthing feature within the Dimension range and to optimise performance further,  
use a shielded or screened loudspeaker cable. The screening termination should be connected to the earth or 'ground' (green)  
terminal on the loudspeaker and to the ground or earth connection on the amplifier. Alternatively if you are not using a  
screened loudspeaker cable but wish to utilise the earthing facility, run a single cable between the earth or 'ground' (green)  
terminal on the loudspeaker to the earth (ground) connection on the amplifier.  
UNPACKING  
WARNING: THESE LOUDSPEAKERS ARE HEAVY - SEEK ASSISTANCE WHEN LIFTING.  
To remove the loudspeakers from the packaging please follow these instructions carefully:  
Lay the carton on the floor noting that the text (OPEN THIS END) on both ends of the box are visible and the arrows on the  
carton ends point towards the floor - in this position the speaker in the carton will be positioned on its back. Remove the  
packing tape from both ends of the carton and fold the carton flaps right back. The spike kit (containing rear spikes, nuts,  
washers, cone tips and floor protection cups) is immediately visible. These accessories are essential for optimum performance  
and for providing a rigid and stable footing for the speaker. The secure interface between the cabinet and the floor brings  
about an improvement in clarity, bass 'speed' and definition.  
To facilitate easier removal of the Dimension speakers from their packaging, the carton side has been fitted with plastic  
locking devices, which allow the carton to be fully opened along its length, and then folded back. To remove each of the  
plastic locks, insert two fingers into the device and pinch the two flat ribs together - this will unlock the ribs and allow the  
whole locking mechanism to be pulled free from the box. Once all the locking devices have been removed, fold back the  
carton to reveal the contents. Carefully remove the packing material from the bottom of the loudspeaker so that this end of  
the speaker can be carefully lowered onto the floor. Follow the rest of the instructions below regarding the fitting of cones  
and spikes BEFORE tilting the speaker into an upright position.  
It is strongly recommended that you store all the packaging to allow protected transportation in future.  
WARNING: IT IS IMPERATIVE THAT THE SPIKES AND CONE TIPS ARE FITTED BEFORE THE SPEAKER IS PLACED  
IN AN UPRIGHT POSITION. FAILURE TO DO SO MAY CAUSE THE SPEAKER (ESPECIALLY TD 12) TO TIP OVER  
WITH THE RISK OF DAMAGE OR INJURY.  
The spikes, along with washers and lock nuts, should be fitted loosely into the threaded holes in the base at the rear of the  
cabinet. The cone tips should then be threaded into the ends of the polished alloy cones at the front of the speaker. Level  
the rear spikes to the front cones by eye then hand tighten the lock nuts. Spike locating cups are provided and these may  
be used to protect sensitive floor surfaces.  
The loudspeaker can now be carefully lifted into an upright position and the packing piece removed from the top panel.  
3. Refer to the paragraph headed 'Positioning' for speaker placement advice.  
4. The alloy side strips of the speaker are protected with a plastic film; it is recommended that this be left on for protection  
and should not be removed until the speaker is fully installed.  
3
 
INSTALLATION  
To avoid potential damage to your loudspeaker, ensure that the amplifier is switched OFF prior to connecting or disconnecting  
any cables. Before switching on double check that all connections are secure and that polarity is correct.  
WARNING: SEE THE SECTION ON SCREENING IF POSITIONING NEAR TO A TELEVISION SCREEN.  
CONNECTION IN SINGLE WIRE MODE  
(See fig. 2)  
Connect the pair of link cables supplied in the accessory kit to each loudspeaker terminal panel as follows:  
Starting with the red (positive) lead, loosen the locking pin which passes through the plug by turning the plastic head of  
the locking pin one full anti-clockwise rotation.  
The 'unlocked' plug can now be inserted into the red (positive) low frequency (LF) terminal on the loudspeaker.  
Tighten the plug by turning the locking pin clockwise until finger-tight.  
The spade connection at the other end of the lead should be connected to the red (positive) high frequency (HF) terminal  
on the loudspeaker. To do this, loosen the terminal nut sufficiently to allow insertion of the spade connector and then  
re-tighten the terminal nut finger-tight.  
Repeat this operation for the black (negative) HF and LF terminals  
Repeat the whole operation for the other loudspeaker  
For optimum performance in single wire mode, loudspeaker cable connections from the amplifier should now be made to  
the high frequency (HF) terminals of the loudspeaker:  
The positive (plus) terminal on the amplifier left channel (marked + or coloured red) must be connected to the positive  
HF terminal on the left speaker. The left speaker is the one on the left as you look at the stereo pair from your listening  
position.  
The negative (minus) terminal on the amplifier left channel (marked - or coloured black) must be connected to the negative  
HF terminal on the left speaker.  
Repeat this connection process for the right speaker. Remember that the positive (+ or red) on the amplifier must be  
connected to the positive (+ or red) on the speaker and the negative (- or black) to negative.  
Select a signal source, such as a CD player; switch on the amplifier and slowly turn up the volume control to check that both  
loudspeakers are reproducing bass and treble information.  
CONNECTION IN BI-WIRE MODE  
(See fig. 3)  
Please note in Bi-wire mode that the link leads, which are supplied in the accessory pack, should NOT be fitted.  
Be sure that the amplifier is switched OFF and then prepare the two sets of cabling for each 'side' of the system separately.  
Measure and cut four lengths of cable, two per speaker. Label two of the cable lengths Left LF and Left HF (low frequency  
and high frequency) then repeat this process for the right pair.  
If your amplifier is not equipped with separate output terminals for bass and treble information then, at the amplifier  
end of the cables, twist the Left LF+ (positive) and the Left HF+ (positive) together. Connect these to the amplifier Left  
channel positive terminal marked + (plus) or coloured red.  
Twist the Left LF- (negative) and the HF- (negative) cables together and connect them to the amplifier Left channel negative  
terminal marked - (minus) or coloured black.  
At the loudspeaker end connect the cables labelled Left LF+ and Left LF- to the left hand loudspeaker LF terminals,  
ensuring that you note the polarity markings on the cable sheathing.  
Then proceed to connect the Left HF+ and Left HF- to the HF terminals on the same loudspeaker.  
Repeat this process to connect the right hand loudspeaker to the amplifier right channel output, once again ensuring  
that polarity is correct throughout.  
Switch the amplifier on with the volume control set at its lowest setting. Select a favourite source and slowly turn up the  
volume to a low level. Check that bass and treble information is being reproduced from both speakers - if not, switch  
off the amplifier and recheck the connections.  
BI-AMPING  
(See fig. 4)  
Bi-amping extends the principle of Bi-wiring one stage further. In this connection option separate power amplifiers are used  
for bass and treble signals in each loudspeaker. Four mono (or two stereo) amplifiers of the same type are required for a  
stereo pair of loudspeakers. Ensure that the cable links between the loudspeaker terminals are removed and that correct  
polarity is maintained throughout.  
If two stereo amplifiers are used, it is recommended that one amplifier supply bass information to left and right loudspeakers  
and the other, the treble information.  
4
 
CONNECTION OF EARTH OR ‘GROUND’ LEAD  
(See figs. 2, 3 and 4)  
To optimise performance further, use a shielded or screened loudspeaker cable. The screening termination should be connected  
to the earth or ground (green) terminal on the loudspeaker and to the ground or earth connection on the amplifier. Alternatively  
if you are not using a screened loudspeaker cable but wish to utilise the earthing facility, run a single cable between the earth  
It is essential that the coupling link cables between the loudspeaker terminals be removed.  
Avoid potential damage to your amplifier - ensure that all connections are secure and the polarity is correct in all wiring.  
POSITIONING AND FINE-TUNING  
(See fig. 5)  
To get best results from your new Tannoy Dimension loudspeakers it is worthwhile spending a little time finding the optimum  
set-up configuration.  
Begin by angling the speakers towards your chosen listening position, usually this is on the centre line of the room, so that  
when seated you can just see the inner side panel of each speaker. The front of the loudspeaker should not be obstructed  
in any way. The loudspeakers should be located between 1.5 to 4.5 metres (5ft to 15ft) apart - with the listening position  
set slightly further away than the speakers are apart. Avoid positioning the loudspeakers in corners of the room, as this  
will have a negative effect on performance. Ideally, maintain a distance of at least 0.5 metres (20 inches) from the rear  
wall, and 1 metre (39 inches) from the side.  
With the speaker in its listening position, rock the loudspeaker gently from side to side so that the spikes find their way through  
the weave of the carpet and on to the solid surface below. Once fine adjustments have been made to the rear spikes, to  
level the loudspeaker and ensure stability, tighten the lock nuts firmly but without using undue force.  
GRILLES  
The Dimension grille has been designed to provide acoustic transparency. However, for ultimate fidelity the enthusiast will  
appreciate the slight improvement in clarity and detail that is achieved by removing the grilles during listening.  
SuperTweeter:  
The mesh grille in front of the diaphragm is held in place by magnetism and may easily, but carefully, removed. It is essential  
that the SuperTweeter diaphragm is not touched, as damage will destroy its performance and require specialist repair by  
your Tannoy dealer.  
Any such damage will not be covered under warranty.  
Grille panel:  
Provided in the accessory pack are six felt covered studs. These are designed to fit into the holes on the front baffle panel  
once the main grille is removed. If the grille is to be refitted the studs should be removed and stored in the six holes provided  
on the inside of the grille frame.  
CARE OF CABINET  
The accessory kit supplied with your Dimension speakers provides the materials necessary to maintain the high quality finish.  
Wood surfaces:  
The real wood veneer cabinets should only be cleaned with a dry cloth or with a light application of quality non-silicone  
furniture polish. Take care not get polish on the velvet surfaces of the loudspeaker. It should be remembered that as a natural  
substance all wood products will change colour when exposed to the UV content of ambient light. Light veneer will darken  
appreciably to a rich natural patina.  
Polished alloy surfaces:  
The polished alloy side rails, cone feet and SuperTweeter housing should be polished using the polishing cloth provided.  
Extra care is needed whilst polishing the SuperTweeter housing and it is recommended that the SuperTweeter protective grille  
is in place so as to avoid damaging the diaphragm.  
Velvet surfaces:  
To remove dust from the velvet and smooth the pile of the velvet material use the non-scratch open weave side of the foam  
pad, which is also to be found in the accessory kit.  
5
 
DIMENSION HOME THEATRE 5.1 – GENERAL INFORMATION  
(See fig. 6)  
Unlike other forms of encoded surround audio, 5.1 offers full bandwidth capability for the surround and centre channels,  
with the ability to treat the subwoofer as a single discreet channel for special effects playback or, for music applications, as  
a dedicated low frequency instrument channel. This places new demands on the surround and centre channel loudspeakers  
in both the mixing environment and the playback environment.  
The 5.1 format allows the mix engineer in the recording studio to assign audio information to one or more discreet channels  
of playback; providing very vivid and exacting localisation for the apparent sound sources in the listening environment. To  
reliably recreate that accurate localisation during playback, the selection and location of loudspeakers becomes the single  
most critical issue next to the talent of the mix engineer in the studio.  
THE SYSTEM  
A fully operational 5.1 system consists of two main front loudspeakers, two rear effects speakers at the rear (usually wall  
mounted) and a centre channel. The subwoofer provides the .1 part of the system.  
SCREENING  
The Dimension loudspeaker drive units contain very large magnets to ensure optimum performance, power handling, efficiency  
and reliability. These are capable of generating a substantial magnetic field extending a considerable distance beyond the  
sidewalls of the speaker enclosure. This field will cause picture distortion if the speakers are placed too close to the TV. It is  
therefore recommended that the front (left and right) speakers are positioned at least 1 metre (39 inches) to each side of  
the television screen. Rear projection and plasma televisions are not prone to interference from these magnetic effects.  
FRONT SPEAKERS  
The ultra wide dynamic range and power handling capability of Dimension loudspeakers will provide the ultimate home  
cinema experience. The speakers should be positioned either side of the TV or projection screen placed in line with the screen  
surface.  
CENTRE CHANNEL SPEAKER TDC1  
(See figs. 2 and 3)  
The Dimension centre channel speakers are fully magnetically shielded and are designed for installation directly above or  
below the TV. As the main effects speaker for the front soundstage, the critical factor in its performance is the placement.  
In all cases the centre channel speaker should be positioned as near to the TV screen as possible. The viewing position when  
seated determines the ideal mounting height, but in all cases this should be as close as possible to ear height. As with the  
main speakers the front baffle panel should be as near as possible in line with the screen surface.  
The Dimension TDC 1 centre channel can be wired in single wire or bi-wire mode. Please refer to the figures 2 and 3 for  
connection guidance bearing in mind that connection should be made to the dedicated centre channel output on your A/V  
processor amplifier.  
REAR EFFECTS SPEAKERS  
The integrity of the special effects soundstage created by the source material will be compromised if the speakers are installed  
on the sidewalls, for that reason they should always be placed behind the main viewing position.  
The placement of floor standing speakers at the rear should mirror as near as possible the location of the front pair and  
0.5 metres (20 inches) from the rear wall. Wall-mounted loudspeakers should be shelf or bracket mounted 1.5 to 4.5 metres  
(5ft to 15ft) apart with a height mounting height range of 1.5 to 2 metres (5ft to 7ft).  
SUBWOOFER TD-SUB  
As the subwoofer only produces low frequency, therefore monaural information, it is difficult to detect its location by ear. It  
could as a result be situated anywhere in the room, but optimum performance will be gained by locating the subwoofer  
between the main stereo pair of speakers. Bass output will increase when placed next to a wall or in a corner so use the  
subwoofer volume control to balance the output with the rest of the system.  
Please refer to the manual supplied with the subwoofer for advice on installation and set-up.  
TRANSLATED .PDF DOWNLOADS OF THIS MANUAL ARE AVAILABLE ON OUR WEBSITE AT  
6
 
TECHNICAL SPECIFICATIONS  
TD8  
TD10  
TD12  
TDC1  
PERFORMANCE  
Recommended amplifier power  
-
Watts RMS 40 - 160  
50 - 200  
130  
480  
91dB  
6
38Hz - 54kHz  
90 º conical  
50 - 280  
180  
675  
92dB  
6
30Hz - 54kHz  
90 º conical  
40 - 200  
130  
480  
92dB  
6
42Hz - 54kHz  
90 º conical  
Continuous power handling - Watts RMS  
Peak power handling - Watts  
Sensitivity (2.83Volts @ 1 m)  
Nominal impedance - Ohms  
Frequency response -6dB  
100  
375  
90dB  
6
42Hz - 54kHz  
90 º conical  
Dispersion  
DRIVE UNITS  
SuperTweeter  
25mm (1") 25 micron  
titanium dome,  
neodymium magnet  
system  
25mm (1") 25 micron  
titanium dome,  
neodymium magnet  
system  
25mm (1") 25 micron  
titanium dome,  
neodymium magnet  
system  
25mm (1") 25 micron  
titanium dome,  
neodymium magnet  
system  
Dual Concentric™ High Frequency  
Dual Concentric™ Low Frequency  
25mm (1") 50 micron  
25mm (1") 50 micron  
25mm (1") 50 micron  
25mm (1") 50 micron  
aluminium dome with aluminium dome with aluminium dome with aluminium dome with  
Tulip Waveguide  
Tulip Waveguide  
Tulip Waveguide  
Tulip Waveguide  
200mm (8") Paper pulp 254mm (10") Paper pulp 300mm (12") Paper pulp 200mm (8") Paper pulp  
cone, with a twin roll  
impregnated fabric  
surround  
cone, with a twin roll  
impregnated fabric  
surround  
cone, with a twin roll  
impregnated fabric  
surround  
cone, with a twin roll  
impregnated fabric  
surround  
Low Frequency  
2 x 200mm (8") Paper  
pulp cone, with a twin  
roll impregnated fabric  
surround  
CROSSOVER  
Dual Concentric™ type  
Bi-wired, hard-wired  
passive low loss,  
2nd order low pass,  
1st order high pass  
Bi-wired, hard-wired  
passive low loss,  
3rd order low pass,  
1st order high pass  
Bi-wired, hard-wired  
passive low loss,  
3rd order low pass,  
1st order high pass  
Bi-wired, hard-wired  
passive low loss,  
1st order low pass,  
1st order high pass  
Frequency  
1.4 kHz  
1.2 kHz  
1.1 kHz  
1.4 kHz  
Low frequency to Dual midrange type  
Bi-wired, hard-wired  
passive low loss,  
1st order  
Frequency  
400Hz  
SuperTweeter type  
Frequency  
3rd order high pass filter 3rd order high pass filter 3rd order high pass filter 3rd order high pass filter  
14kHz  
14kHz  
14kHz  
14kHz  
CABINET  
Enclosure type  
Dual chamber coupled Twin port reflex  
reflex  
Twin port reflex  
Closed box  
Construction  
High-density 18mm  
birch-ply enclosure,  
High-density 18mm  
birch-ply enclosure,  
High-density 18mm  
birch-ply enclosure,  
High-density 18mm  
birch-ply enclosure,  
internally cross-braced internally cross-braced  
internally cross-braced internally cross-braced  
High-density 30mm  
birch ply front baffle  
High-density 30mm  
birch ply front baffle  
High-density 40mm  
birch ply front baffle  
High-density 30mm  
birch ply front baffle  
Dimensions mm (inches)  
943 x 299 x 305  
(37.1 x 11.8 x 12)  
1095 x 350 x 370  
(43.1 x 13.8 x 14.6)  
1254 x 435 x 435  
(49.4 x 17.1 x 17.1)  
373 x 774 x 420  
(14.7 x 30.5 x 16.5)  
Volume litres  
38  
67  
110  
63  
Weight kgs (lbs)  
Finish options  
22 (48.5)  
32 (70.5)  
52.5 (115.7)  
31.5 (69.4)  
American cherry with  
polished alloy trim or  
Rose-nut with black  
anodised alloy trim  
American cherry with  
polished alloy trim or  
Rose-nut with black  
anodised alloy trim  
American cherry with  
polished alloy trim or  
Rose-nut with black  
anodised alloy trim  
American cherry with  
polished alloy trim or  
Rose-nut with black  
anodised alloy trim  
Optional Accessories  
Front grille assembly  
7
 
SET-UP DIAGRAMS  
SINGLE WIRE MODE AND EARTH (GROUND)  
LEAD CONNECTION  
TERMINAL PANEL CONNECTIONS  
FIG. 1  
FIG. 2  
TO RIGHT  
SPEAKER  
HIGH FREQUENCY  
NEGATIVE(-) TERMINAL  
HIGH FREQUENCY  
POSITIVE(+) TERMINAL  
HF+  
HF+  
+
-
+
-
L
R
LF-  
POWER AMPLIFIER  
LF-  
LF+  
LF+  
LOW FREQUENCY  
POSITIVE(+) TERMINAL  
LOW FREQUENCY  
NEGATIVE(-) TERMINAL  
TO 'GROUND' OR  
'EARTH' CONNECTION  
'EARTH' OR 'GROUND' TERMINAL  
ON AMPLIFIER (OPTIONAL)  
LINK WIRES IN PLACE  
BI-WIRE MODE AND EARTH (GROUND)  
LEAD CONNECTION  
BI-AMPING MODE AND EARTH (GROUND)  
LEAD CONNECTION  
FIG. 3  
FIG. 4  
TO RIGHT  
SPEAKER  
HF+  
+
-
+
-
HF+  
L
R
HIGH FREQUENCY  
POWER AMPLIFIER  
TO RIGHT  
SPEAKER  
LOW FREQUENCY  
POWER AMPLIFIER  
LF-  
LF+  
L
R
+
-
+
-
LF-  
LF+  
TO 'GROUND' OR  
'EARTH' CONNECTION  
ON HIGH FREQUENCY  
AMPLIFIER (OPTIONAL)  
TO RIGHT  
SPEAKER  
+
-
+
-
TO 'GROUND' OR  
L
R
'EARTH' CONNECTION  
ON AMPLIFIER (OPTIONAL)  
POWER AMPLIFIER  
LINK WIRES REMOVED  
LINK WIRES REMOVED  
8
 
SET-UP DIAGRAMS  
POSITIONING RECOMMENDATIONS - TWO CHANNEL STEREO  
FIG. 5  
0.5 METRES OR MORE  
1.5 TO 4.5 METRES  
1 METRE  
OR MORE  
POSITIONING RECOMMENDATIONS - HOME CINEMA  
FIG. 6  
SUB  
9
 
Tannoy Limited, Home Audio Division, Coatbridge, Scotland, ML5 4TF.  
Tel: +44 (0) 1236 420199 Fax: +44 (0) 1236 428230  
Tannoy/TGI North America Inc., Suite 1, 335 Gage Avenue, Kitchener, Ontario, Canada N2M 2C8.  
Tel: (519) 745-1158 Fax: (519) 745-2364  
Tannoy Nederland b.v., Anthonetta Kuijlstraat 19, 3066 GS Rotterdam.  
Tel: (010) 2860555 Fax: (010) 2860431  
 

Sharp PDAs Smartphones EL 6985 User Manual
Sherwood Stereo Receiver R 963 User Manual
Shindaiwa Trimmer T261 EVC User Manual
Sony Camera Accessories LSFVHA User Manual
Sony Clock Radio SY ICF C8WM User Manual
Sony DVD Player DVP SR210P User Manual
Sony Security Camera SNC RH124 User Manual
Southern Telecom Headphones SNC200 User Manual
Sterling Plumbing Indoor Furnishings 442007 U User Manual
Sun Microsystems TV Video Accessories AND B100S User Manual